4-041-03-0084 4041030084 Homag Edgebander Heating Lamp KW 600W 115V LB=60

Replacing a failed preheating lamp on a Homag edgebander should not stop the line. This is the edgebander heating lamp rated 600 W at 115 V, supplied in the LB=60 variant and listed under Homag part numbers 4-041-03-0084 (4041030084) and 4-060-18-0081 (4060180081). It heats the edge band and the glue line as they pass the preheating position, so the adhesive flows before the joint is pressed cold. Price is negotiable and orders ship by DHL, FedEx or UPS. It is a woodworking machinery spare part, not an assembly.

A workshop running an edgebander meets the same three problems: the preheating lamp fails, the glue line starts bonding cold and the band lifts at the ends of the panel; a lamp is ordered against a guessed number, arrives at the wrong wattage and the machine waits; and the same lamp is quoted at a different figure every time it is asked for.

This lamp closes all three. It is an edge preheating lamp for Homag edgebanding machines, rated 600 W at 115 V and supplied in the LB=60 variant. Fixed in the preheating position, it raises the temperature of the band and the glue line before the joint is pressed, so the adhesive flows and the edge closes instead of sitting cold. Wattage and voltage must match the lamp being replaced.

Two numbering styles identify it. The machine side lists the part as 4-041-03-0084, written 4041030084 without dashes, and the supply side lists the same lamp as 4-060-18-0081, written 4060180081. Order either pair and you order the same 600 W, 115 V, LB=60 lamp, not a similar one.

Price is negotiable and shipments go out by DHL, FedEx or UPS. Because two numbering styles exist, quote both numbers when you enquire; the order is checked against 600 W, 115 V and LB=60 before it is packed.

Six things decide whether this is the lamp that goes back into the preheating position.

• 600 W heating output — the rated figure of this lamp, carried in the part listing. Wattage is what sets how much heat reaches the glue line, so a lower-rated lamp is a different part.
• 115 V rating — the rating printed on the lamp. Check that the lamp coming out of the machine reads 115 V before the new one goes in.
• LB=60 variant — the third figure in the designation. 600 W, 115 V and LB=60 belong to one lamp, so replace like with like rather than by wattage alone.
• Two part numbers, one lamp — 4-041-03-0084 and 4041030084 on the machine side, 4-060-18-0081 and 4060180081 on the supply side, all for this single lamp.
• Edge preheating function — the lamp heats band and glue line at the preheating position, so the adhesive is already mobile at the moment the joint is pressed.
• Listed for Homag edgebanders — catalogued as a Homag edgebanding machine part, so it takes the lamp position already in the machine without modifying the machine.
• Spare-part supply — categorised as a woodworking machinery spare part: one lamp per order, not a machine assembly to strip down.
• Courier shipment — DHL, FedEx or UPS, whichever service your workshop already receives on.

A buyer with a dead lamp has two offers on the table: wait for a quotation from the machine supplier, or buy something that looks the same. Both have a cost, and this lamp is aimed at removing that choice.

• Right rating at the first attempt. 600 W, 115 V and LB=60 are written on the page instead of being assumed, so the lamp that arrives matches the lamp that came out and the line restarts once.
• Both number formats covered. 4-041-03-0084 and 4-060-18-0081, with or without dashes, all resolve to this one lamp, so an order does not bounce back over a formatting difference.
• Same position, no modification. the lamp goes into the preheating position it is listed for, so nothing on the edgebander has to be reworked to accept it.
• Consumable cost, not machine cost. it is a spare part rather than an assembly, and the price is negotiable, so replacing a failed lamp stays a small line on the maintenance sheet.
• Shipment on a service you already use. DHL, FedEx or UPS means the lamp follows the same courier route and paperwork as your other parts.
• Order by number, not by photograph. with four number forms published, the lamp can be ordered from the part list without measuring anything or waiting for a photo to be interpreted.

Either one. Both numbers describe the same lamp: 4-041-03-0084 is also written 4041030084, 4-060-18-0081 is also written 4060180081, and all four point to the 600 W, 115 V, LB=60 lamp on this page. Quote whichever number is on your own part list.

Both, on the same lamp. 600 W is the wattage and 115 V is the lamp's rating; the listing carries the two together because a lamp needs both figures to be the right part.

It is part of the lamp designation, so yes, it has to match. Order the lamp as 4-041-03-0084 / 4041030084 with LB=60 and compare it with the marking on the lamp you are taking out before fitting.

Yes if your machine takes the LB=60, 600 W, 115 V lamp. It is listed for Homag edgebanding machines and goes into the preheating position the old lamp came out of, so compare the marking on your old lamp with the numbers above before you order.

Yes. It is one replacement part rather than an assembly, and the machine needs no modification to accept it. Power the edgebander down, fit the new lamp in the same position and restart the preheating cycle.

No. It is supplied as a woodworking machinery spare part under the Homag numbers shown above. If your purchasing paperwork calls for an original branded part, say so before the order is placed.

By courier: DHL, FedEx or UPS. The shipment field on this listing covers those three services, so name the one your workshop normally receives on.

The price is negotiable, so no fixed figure sits on the page. Send the part number you use, 4-041-03-0084 or 4-060-18-0081, and the quantity you need, and the lamp is quoted against that.