Cutting Edges Replacement For Cutter Head - Woodworking Edgebander Tool

Need to keep a cutter head cutting clean without buying a new head? The 44044066 replacement edge is the drop-in part: each insert is 14 x 14 x 4 mm, bored 6 mm, and built from PCD + alloy. A dull edge comes off the head and a new one goes into the same seat, so the cutting circle stays where it was set. Heads on edge banding machines, planers, jointers and milling units that take this insert size keep running instead of waiting for an outside sharpening shop.

A dull cutter head shows three ways: feathered banding, tear-out on veneered board, and a machine idled while the head goes to a sharpening shop. A second head covers the wait and doubles cost; worn edges send the reject rate up. The 44044066 replacement edge takes the third route: change the edge, keep the head.

Each edge is a square insert of 14 x 14 x 4 mm, 4 mm thick, with a 6 mm inner bore. The build is PCD + alloy: a PCD cutting edge on an alloy body, so the face against the panel is diamond-grade and the clamped body stays tough. The insert sits in the seat already machined into the head, so nothing is re-cut and the cutting circle does not move.

Profiles are dimensioned so each insert repeats the geometry of the one it replaces. Renew all edges together and the trim stays even across the banding width. At 14 x 14 x 4 mm it adds little mass to the cutting circle, which is what light, quiet running on thin panel asks for.

The inserts fit edge banding cutter heads, and the same format serves planer, jointer and milling heads. Send the head model or a photo of the edge you run and the fit is confirmed first. Price is quoted per request; shipping is by air, sea or express.

What sets these edges apart is the combination of seat size, cutting material and how the change is made.

• 14 x 14 x 4 mm seat size - length 14 mm, width 14 mm, thickness 4 mm; check all three against the pocket in your head.
• 6 mm bore, one screw - the 6 mm centre hole takes a single fixing screw, so the change needs one tool, not a strip-down.
• PCD + alloy body - PCD forms the cutting edge, an alloy body carries the seat load; hard edge, tough back.
• Change the edge, keep the head - worn inserts lift out and new ones drop into the same pocket, so head balance and machine set-up survive.
• Repeatable geometry - profiles repeat the shape of the insert they replace, so the trim does not change when the edge is renewed.
• Runs light and quiet - a 14 x 14 x 4 mm insert keeps mass at the cutting circle low, the condition for quiet panel processing.
• Short set-up - the pocket is untouched, so re-setting comes down to screw torque and one test trim.
• Not only edge banding - the same insert format serves planer, jointer and milling heads, one line item for several stations.
• Clean trim, less rework - a fresh edge cuts banding and panel in one pass, so touch-up on the trimmed edge drops.

The usual choice is between sending the head out, buying a second head, or running a dull edge. A replaceable edge removes that choice.

• Swap the edge, keep the head. The money goes on a 14 x 14 x 4 mm wear part instead of a complete head whose body is still good.
• No special tooling. One 6 mm screw, one pocket, one test trim; nothing in the change needs a press or a balancing shop.
• Same cutting circle every time. Because the head is never re-machined, trim height stays exactly where the machine was set.
• Minutes instead of days out of the line. A change at the machine replaces a sharpening round trip that takes the head off production.
• Even trim across the banding. Renew all edges on the head together and the profile stays uniform from the first panel to the last.
• One part number across stations. Planer, jointer and milling heads use the same insert format, so 44044066 can cover the trim station and the other heads.
• Quieter, lighter cutting. Less mass at the cutting circle means less load on the spindle and less noise at the head, panel after panel.

They are 14 x 14 x 4 mm square inserts with a 6 mm inner bore. Length is 14 mm, width 14 mm, thickness 4 mm - measure the pocket and the screw in your head against those four numbers.

Only the replacement edges. The part replaces the worn cutting edges in a cutter head you already have, which is why the head itself does not have to be bought or re-machined.

PCD + alloy. A PCD cutting edge is combined with an alloy body, so the edge that meets the panel takes the cutting load and the body takes the clamping load.

No. Each edge is held by one screw through the 6 mm bore, so a standard driver, a clean pocket and one test trim on scrap board cover the whole change.

Only if its cutter head takes a 14 x 14 x 4 mm insert with a 6 mm bore. Send the head model or a photo of the edge you are running and the fit is confirmed before the order ships.

Yes, where those heads take the same seat. The insert format also serves planer, jointer and milling heads, so one part number can cover several stations in the shop.

When the trim stops cutting clean - feathered banding, tear-out on veneer, or a whisker of glue left on the edge. That is the point to swap the insert rather than press a dull edge harder.

Price, minimum order and lead time are quoted per request, because all three depend on how many edges your heads carry. Send the head count and edges per head for a quote with air, sea and express options.