Edgebanding Machine Carbide Scraping Blade Inserts 22.3x14x2 R2

Product Description

Need to clear a glue line after the trimming station without swapping the whole scraper unit? This is the insert that does it: 22.3 mm long, 14 mm wide, 2 mm thick, R2 corner radius, 4.7 mm fixing hole, solid carbide, supplied in left-hand and right-hand direction for Homag edgebanding machines. It replaces 4-014-03-0311, 4014030311, 4-014-03-0306 and 4014030306. Price is quoted on request, so tell us the quantity you run per month.

Every edgebander runs into the same three things on a normal shift: a glue line still visible after the last trimming station, scraper inserts that dull and start chipping PVC instead of shaving it, and a reorder that has to match the exact part number stamped on the holder. The carbide insert scraper 22.3x14x2 R2 is built for that third station, where all three problems meet.

It is a solid carbide scraping blade insert: 22.3 mm long, 14 mm wide, 2 mm thick, with an R2 corner radius and a 4.7 mm fixing hole. It seats in the scraper holder of Homag edgebanding machines and is listed in both left-hand and right-hand direction, so a matched pair goes on without filing, shimming or re-drilling the holder.

Carbide is why the insert survives a production shift. The ground edge holds its angle against a filled glue line on PVC, ABS, melamine and veneered edges, and the R2 profile runs along the panel corner instead of digging into the face below it. Because the insert is a separate 2 mm plate, the holder stays bolted to the machine and only the plate is changed once the edge stops shaving clean.

Four numbers cover this one item: 4-014-03-0311, 4014030311, 4-014-03-0306 and 4014030306. Price is quoted on request.

Product Features

Ten details that decide whether this insert fits your holder.

• Carbide body, not tool steel — a solid 2 mm plate whose edge keeps its angle through a shift instead of being re-honed.
• R2 corner radius — the 2 mm radius runs along the panel corner and shaves the glue line without cutting into the face.
• 4.7 mm fixing hole — one 4.7 mm fixing point, so the insert seats in the same position every time.
• Left and right direction — both hands are listed, so a pair is fitted together and the edge is scraped from both directions.
• 22.3 x 14 mm face — 22.3 mm edge length and 14 mm width, enough contact without overhanging the holder.
• Homag holder geometry — the pattern matches the Homag scraper station, so the insert drops into the existing holder with no adapter plate.
• Four part numbers, one insert — 4-014-03-0311, 4014030311, 4-014-03-0306 and 4014030306 all resolve to this 22.3x14x2 R2 item.
• Edge materials covered — PVC, ABS, melamine and veneer edges are all scraped with the same insert.
• Single-screw swap — the holder stays bolted to the machine; only the 2 mm plate comes off its one fixing screw.
• Consumable, so stock is cheap to hold — keep 2 spares per station on the shelf, not a second scraper unit.

Product Parameters

Product Advantages

If you are scraping glue lines today, the choice is usually a complete scraper unit or a hand touch-up. This part takes the third option.

• You buy the wear part, not the assembly. The 2 mm plate wears out long before the holder does, so replacing the insert alone keeps the station on the machine.
• Downtime measured in one screw. One fixing screw at 4.7 mm is the whole changeover, so a station can be back in production without re-aligning the holder.
• Part numbers that match what is on the holder. 4-014-03-0311 and 4-014-03-0306 are both listed with their undashed forms, so the number on the old insert can be checked line by line.
• Both hands in one listing. A station that runs left and right can order one line instead of chasing two separate part numbers.
• The R2 radius protects the panel. A 2 mm corner keeps contact on the glue line, which is what stops a sharp insert from marking the board face.
• Carbide keeps the angle. The edge is ground in carbide, so it holds its scraping angle on PVC, ABS, melamine and veneer edges through a full shift.
• Two spares per station is enough cover. Because the item is a 22.3x14x2 mm consumable, shelf stock stays small.

Frequently Asked Questions

Will this insert fit my Homag edgebander?

Yes, if your holder takes the 22.3x14x2 R2 pattern. The insert is 22.3 mm long, 14 mm wide and 2 mm thick with a 4.7 mm fixing hole, which is the Homag scraper station geometry — check the number on your old insert against 4-014-03-0311 or 4-014-03-0306 before ordering.

Do I need one left-hand and one right-hand insert?

Yes, if your station runs a pair. Both directions are listed under this one item, so you can order left and right on the same line instead of hunting two part numbers.

How long does one insert last?

Until the edge stops shaving the glue line clean — there is no fixed hour count, because it depends on the glue line and the edge material. Carbide holds the R2 profile far longer than tool steel, and the plate is cheap enough to keep spares on the shelf.

Will it scratch the panel face?

No, that is what the R2 radius is for. The corner is rounded to 2 mm, so contact stays on the edge and the glue line instead of the flat of the board.

Does it work on PVC and ABS edges?

Yes. PVC, ABS, melamine and veneer edges are all scraped with this insert, one insert per station.

How do I change the insert?

Undo the single fixing screw, lift the 2 mm plate out and seat the new one on the same 4.7 mm hole. The holder stays bolted to the machine, so nothing has to be re-aligned.

Can I buy the insert without the whole scraper unit?

Yes. This is listed as scraping blade inserts only, not as a complete scraper assembly, so you replace the wear plate and keep the holder.

What are the four part numbers for?

They are two numbering styles of the same insert. 4-014-03-0311 and 4014030311 are one number with and without dashes, and 4-014-03-0306 and 4014030306 are the second pair; all four are listed for this 22.3x14x2 R2 item.