55mm Cutting Edgebanding Machine Tool Professional End Cutting Device Manual Cutter

Need to cut a banding end square without walking the panel back to the machine? This 55 mm end cutter does it by hand. A cutting width of 0–55 mm covers every banding width the data lists, and a cutting thickness of 0.3–3.0 mm covers thin PVC through 3 mm ABS. PVC, ABS, melamine and veneer all run on the same cutter. The body is 27.5 x 8 x 13 cm, 0.8 kg net and 1.3 kg gross, black, made in China, operated manually.

Three problems show up at the end of a banding run. A knife dragged across 3.0 mm ABS tears the corner instead of shearing it, and the tear shows under a clear finish. A file brings the corner back rounded, and a rounded corner is a reject on a square cabinet. Trimming the offcut on the machine means re-clamping a finished part.

This manual end cutter takes all three off the machine. It is a hand-held end cutting device for edgebanding, with a cutting width of 0–55 mm and a cutting thickness of 0.3–3.0 mm. One cutter covers the whole banding rack: PVC, ABS, melamine and veneer, so a mixed order needs no second trimmer.

The range is what separates it from a fixed cutter on the machine. 55 mm is the widest banding it takes and 0.3 mm the thinnest strip, so one body handles a 0.3 mm PVC roll and a 3.0 mm ABS edge. The cut is made by hand where the panel already sits.

The body is 27.5 x 8 x 13 cm in black, 1.3 kg gross and 0.8 kg net, the 0.5 kg difference being packing. Origin is China. For a shop that bands its own panels, that is one trim at the bench instead of one more pass on the machine.

What a 0–55 mm cutting range and a 0.8 kg body decide at the bench:

• 55 mm cutting width — The 0–55 mm range covers every banding width the product data lists, so one cutter sits at the end of the bench instead of four.
• 0.3–3.0 mm cutting thickness — From a 0.3 mm PVC strip to a 3.0 mm ABS edge, both ends of the range sit inside the same cutter.
• Four banding materials — PVC, ABS, melamine and veneer are the listed strip types, so a mixed order runs on one cutter.
• End cutting, not general trimming — It is a dedicated end cutting device, not a trimmer: the job is the banding end and the overhang at the panel corner.
• Manual operation — The cut is made by hand: no air line, no cable, nothing to set up before the first panel.
• 0.8 kg net weight — 1.3 kg gross against 0.8 kg net leaves 0.5 kg of packing; the tool itself is a one-hand weight.
• 27.5 cm body — 27.5 x 8 x 13 cm overall: an 8 cm width to grip, a 27.5 cm length that keeps the hand clear of the panel face.
• Black body — A black tool reads against pale melamine and light veneer, where a steel-grey cutter gets left on the bench.

Between a knife that tears 3.0 mm ABS and a walk back to the machine for the last 55 mm:

• The panel stays clamped. The end is cut where the panel already sits, so a finished part is not re-clamped on the machine for the last 55 mm.
• One cutter covers the rack. 0–55 mm width and 0.3–3.0 mm thickness mean a 0.3 mm PVC roll and a 3.0 mm ABS edge use the same tool.
• A mixed order stops stalling. PVC, ABS, melamine and veneer are all listed, so four materials in one week do not turn into four tools.
• The corner stays square. It cuts the banding end off instead of rubbing it back, so the corner is not rounded over by a file.
• Light enough for the last panel. 0.8 kg net is a one-hand weight, and 1.3 kg gross is what arrives, including 0.5 kg of packing.
• Fits the bench you already have. 27.5 x 8 x 13 cm needs no bench space of its own and no compressed air, because the cut is manual.
• The width is known before you buy. 0–55 mm is on the product data, so measure the widest banding on your rack against 55 mm before ordering.

Up to 55 mm. The cutting width is listed as 0–55 mm, so the cutter spans from the narrowest strip on the rack to a 55 mm edge.

No. PVC, ABS, melamine and veneer are the four strip types listed for this cutter, so the same tool covers both materials and the materials in between.

3.0 mm. The cutting thickness range is 0.3–3.0 mm, so 0.3 mm PVC and a 3 mm ABS edge both fall inside the same setting.

It is a hand tool. The product is listed as a manual cutter and an end cutting device, and the operation field says manual.

0.8 kg net and 1.3 kg gross, measuring 27.5 x 8 x 13 cm. The 0.5 kg gap between net and gross is the packing.

Veneer is one of the four listed materials (PVC, ABS, melamine, veneer), so the cutter is specified for it. Veneer is the thinnest of the group, so keep it inside the 0.3 mm lower limit of the range.

Made in China, sold under the SHUNHONGYU brand. Country of origin is listed on the product data as China.

Price is quoted per order. The product data lists Contact us for a quote and gives no MOQ, lead time or payment terms, so those are confirmed in the quotation rather than printed on this page.