20x12x2x2mm R1.5 Carbide Scraper Replacements for SCM Edgebanders 0312960703G 0312960702E 0312960700A 0312960701C

Need the scraper that clears the glue line on an SCM edgebander? This is the R1.5 carbide scraping insert for the scraping station, 20 x 12 x 2 mm, listed under SCM number 0312960703G. The same insert body is also ground as R1 0312960702E, R2 0312960700A and R3 0312960701C. Tungsten carbide as standard, PCD available, and it is also listed for Homag machines. Measure the insert you are removing before you order.

A scraping station fails in three predictable ways: the R1.5 radius wears flat and the glue line shows through the finish again, a substitute insert arrives a fraction off size and leaves a step along the edge, and the machine waits while somebody hunts the right SCM number in a printed parts list. This insert closes all three.

It is a scraping knife - the carbide insert that rides behind the trimming cutters and lifts the last of the glue line and edge overhang off the panel. The body is 20 x 12 x 2 mm: 20 mm long, 12 mm high, 2 mm thick. The edge is ground to R1.5, so it follows the rounded corner of the edge instead of cutting a flat step into it.

The edge is tungsten carbide, and PCD is also available for the same holder. The R1.5 profile is listed as SCM 0312960703G, and the family is complete: 0312960702E for R1, 0312960700A for R2, 0312960701C for R3 - four radii, four numbers, one insert shape.

It is listed for SCM edgebanding machines and for Homag machines taking the same 20 x 12 x 2 mm insert. Customization is supported, so a radius outside the four profiles is a question rather than a dead end. Price is quoted per order: send the SCM number and the quantity.

What the numbers on this insert decide, line by line:

• 20 x 12 x 2 mm body - 20 mm long, 12 mm high, 2 mm thick. A caliper against the insert you are removing settles the fit before anything else.
• Edge ground to R1.5 - a true radius on the scraping edge, so it follows the rounded corner of the band instead of shaving a flat step.
• Tungsten carbide edge - the material named for this part, so the 2 mm body scrapes adhesive and edge residue rather than slicing the panel face.
• Four SCM numbers, one family - R1.5 0312960703G, R1 0312960702E, R2 0312960700A, R3 0312960701C: the radius is the only thing that changes.
• Listed for SCM and Homag - two machine families on one listing, so a plant running both keeps a single scraping insert in the spares cabinet.
• Scraping-station part - the insert works after the trimming cutters, which is why its edge is a ground radius and not a serrated cutter profile.
• Customization supported - a radius or a quantity outside the four listed profiles is handled as a custom request under the same 20 x 12 x 2 mm envelope.
• Straight swap at the holder - pull the worn insert out, seat the new one: a 2 mm consumable, not a reground tool.

Two bad options at the scraping station: run a worn radius until the glue line has to be hand-finished, or buy a lookalike insert that sits a fraction off and leaves a step.

• A worn scraping edge becomes a swap, not a shutdown. The insert is 2 mm thick and sits in its holder, so a spare on the shelf puts the station back in production the same shift.
• The glue line stops being a hand-finishing job. An R1.5 radius that still matches the edge profile lifts the residue the trimming cutters leave behind, at the machine, on every panel.
• Four profiles, four numbers, no guesswork. 0312960703G, 0312960702E, 0312960700A and 0312960701C map one-to-one onto R1.5, R1, R2 and R3, so the parts list and the holder agree.
• Three dimensions settle the fit. 20 x 12 x 2 mm is the whole fit decision, so a caliper and the old insert are enough to order without a photo exchange.
• One insert across SCM and Homag. Both machine families are on the listing, so a shop with mixed brands keeps one scraping insert code instead of two.
• Material choice on one part number. Tungsten carbide as standard, PCD on request, in the same 20 x 12 x 2 mm body - the insert shape stays fixed while the edge material follows the job.

0312960703G. That is the SCM number for this 20 x 12 x 2 mm insert ground to R1.5; the other three radii carry their own numbers, 0312960702E for R1, 0312960700A for R2 and 0312960701C for R3.

Only if three dimensions match: 20 mm long, 12 mm wide, 2 mm thick. Measure the insert you are removing before ordering - the part is listed for SCM edgebanding machines, and the size check is what confirms the fit.

Yes, when the holder takes a 20 x 12 x 2 mm insert. The listing covers Homag as well as SCM edgebanding machines, and the three dimensions are the deciding factor.

The radius only. 0312960703G is R1.5, 0312960702E is R1, 0312960700A is R2 and 0312960701C is R3; length, width and thickness stay at 20 mm, 12 mm and 2 mm.

Tungsten carbide. PCD is also available in the same 20 x 12 x 2 mm format, so the edge material can be chosen while the insert shape stays unchanged.

At the scraping and edge-finishing station, after the trimming cutters. It removes the glue line and edge overhang the cutters leave behind, which is why the edge is a ground radius rather than a cutter profile.

Yes. Customization is supported, so a radius outside R1.5, R1, R2 and R3 is handled as a custom request; send the drawing or the dimensions you need with the quantity.

Per order, on request. Send the SCM number, the radius and the quantity you need and the quote comes back against that line; this listing carries no published price.