1 Pair 100X30XH50 Diamond PCD Woodworking Machinery Tools PCD Pre Milling Cutter

Need the panel edge squared before the band goes on? The PMC203 does that job at the pre-milling station. 100 mm outer diameter on a 30 mm bore, 50 mm height, 3.85 kg per pair, sold as 1 pair = 2 pcs. Alloy steel body, PCD diamond cutting edges, and it machines PVC, ABS and wood on woodworking edge banding machines. Fine and rough trimming cutters are supplied from the same list, and other sizes are quoted on request.

Three things decide whether an edgebanding line runs clean, and none shows up on a quotation. The panel edge reaches the glue pot torn instead of square. The band bridges that torn fibre and lifts a few weeks later. A replacement arrives on the wrong bore, so the machine stops while the operator sands edges by hand.

The PMC203 is a PCD pre milling cutter, catalogued as an edgebanding cutter and premilling tool. It mounts at the pre-milling position and squares the panel edge before the band is applied, so glue and band meet cut fibre. One unit is 1 pair, 2 pcs — the pair the station runs on, not a single disc.

The size string 100X30XH50 is the whole fitment: 100 mm outer diameter, 30 mm inner diameter, 50 mm height. The body is alloy steel; the edges are PCD, polycrystalline diamond, the part that meets the board. The pair weighs 3.85 kg, light enough for a one-person changeover.

It covers the materials an edgebanding line already feeds: PVC, ABS and wood, in furniture and interior decoration work. Fine trimming cutters and rough trimming cutters are supplied too, so a worn set is one enquiry rather than three. Other sizes exist beyond the 100 mm disc, customisation is supported, and the pair ships in carton boxes at a quoted price.

What separates a premill cutter that squares an edge from one that only rubs it:

• 100 mm outer diameter. The disc measures 100 mm across, the size written into 100X30XH50.
• 30 mm bore. The inner diameter is 30 mm; another arbor size needs another cutter, not a shim.
• 50 mm height. H50 in the size string is the height, so 100 / 30 / 50 mm settles fitment before an order.
• 3.85 kg per pair. That is the net weight of both cutters, so changeover stays a one-person job.
• 1 pair = 2 pcs. The unit is a matched pair; one order does not leave the station a disc short.
• PCD on alloy steel. Polycrystalline diamond forms the edge and the steel body carries it, so the hard material sits where the chip forms.
• Pre-milling, not trimming. It cuts the panel edge before the band goes on; trimming cutters run after the glue.
• PVC, ABS and wood. One pair covers the three materials an edge banding line handles.
• Trimming cutters from the same list. Fine trimming and rough trimming cutters are supplied alongside the pre-milling pair.
• Other sizes, customisation. Discs beyond 100 mm are quoted on request; PMC004 belongs to the same range.
• Carton box packing. Each pair leaves in a carton box.

When a premill cutter dulls you get two options: keep running and sand edges by hand, or stop the line and wait for a disc nobody confirmed. What this pair changes:

• Fitment is settled on paper. 100 mm outer, 30 mm bore, 50 mm height either matches your spindle or it does not, and you know before money moves.
• The band lands on cut fibre. Pre-milling removes the torn edge that glue would otherwise bridge, which is what keeps a seam flat instead of lifting.
• One unit is a full pair. 2 pcs at 3.85 kg per pair means the station is covered by a single order line, not two.
• Diamond sits where the chip forms. PCD edges on an alloy steel body put the hard material at the contact point, not behind it.
• One pair, three materials. PVC, ABS and wood run on the same cutter, so changeover does not wait on a second disc.
• A worn trimming set is one enquiry. Fine trimming and rough trimming cutters come from the same source as the pre-milling pair.
• A reorder is a model number. PMC203 plus 100X30XH50 identifies the pair completely, so the second order is a copy of the first.

Yes, if your pre-milling station takes a 100 mm disc on a 30 mm bore at 50 mm height. That is exactly the size string 100X30XH50, and the cutter is listed for woodworking edge banding machines.

Two cutters. One unit is 1 pair — 2 pcs, and the pair weighs 3.85 kg net, so the figure covers both discs.

100 mm outer diameter, 30 mm inner diameter, 50 mm height. Those are the three numbers in 100X30XH50.

PCD — polycrystalline diamond — on an alloy steel body. The diamond is the edge that meets the board; the steel body carries it.

PVC, ABS and wood. The cutter is catalogued for woodworking edge banding machines in furniture and interior decoration production.

Pre-milling. It squares the panel edge before the band is applied, while fine trimming and rough trimming cutters cut the band after gluing.

Yes. Fine trimming cutters and rough trimming cutters are supplied alongside this pre-milling pair, and other sizes such as PMC004 are part of the range.

Carton boxes, price quoted per order. Send the model PMC203 and the quantity you need, since the price is quoted rather than listed.