1 Pair 80x30xH63 3+3Z Edgebanding Cutter PCD Pre Milling For Edge Trimming

Need a premilling cutter pair that goes straight back into an edgebander already on the floor? The PMC004 is a PCD pre-milling cutter supplied as 1 pair – 2 pcs: 80 mm outside diameter, 30 mm bore, 63 mm height, 3+3Z tooth layout, 2.84 kg per pair. It shears the panel edge ahead of the glue pot on wood and plastic banding, and it is listed for KDT, NANXING and Homag machines. Custom sizes quoted on request.

An edge bander starts losing the joint at the premilling station, in three familiar ways: the tips dull and push the panel instead of shearing it, the torn edge then shows through under the glued band, and the line stops while a fitter re-sets the unit. The PMC004 premilling cutter pair is the part that answers all three.

It is a PCD pre-milling cutter set for edgebanding machines, listed as 80x30xH63 3+3Z: 80 mm outside diameter, 30 mm bore and 63 mm cutting height, with a 3+3Z tooth layout. The cutting edges are polycrystalline diamond, the surface that meets the panel and the banding material on every pass.

Premilling is the cut ahead of the glue pot, so this pair takes the panel edge before any adhesive reaches it: an 80 mm rim on a 30 mm bore, 63 mm of cutting height, and 2.84 kg per pair — light enough for one fitter to change at the station without lifting gear.

Each order unit is 1 pair – 2 pcs, so both cutters on the head come off at the same interval and the edge stays symmetrical. It is listed for edgebanding premilling on wood and plastic banding material, on KDT, NANXING and Homag machines. A size outside this list is quoted against your cutter or drawing, and price follows the quantity on the enquiry.

Six numbers and one material decide what this pair does at the premilling station:

• PCD on both cutters — polycrystalline diamond is the wear surface named for these blades, on both cutters of the pair.
• 80 mm outside diameter — the rim that sets the cut on the premilling spindle; measure it on the unit, not on a worn cutter.
• 30 mm bore — the seat that centres the cutter on the spindle shaft, and the number a fitment check turns on.
• 63 mm cutting height — one setting covers a 63 mm band height, so the head is not shimmed between band thicknesses.
• 3+3Z tooth layout — the tooth designation sits inside the size callout, so it travels on the order line.
• 1 pair – 2 pcs — supplied as a matched pair, so both cutters on the head are changed together and the edge stays symmetrical.
• 2.84 kg per pair — one fitter, no lifting gear, one change at the station.
• Wood and plastic banding — the listing names both banding materials for this premilling tool.
• KDT, NANXING and Homag — the machines the listing names for this line of trimming cutters, with the size callout as the final check.
• Custom sizes — customization is a listed service, so a bore or height outside 80x30xH63 is quoted from your drawing or measured dimensions.

What changes for a shop that has been running a dull premilling pair to the end of the shift, or waiting for a regrind to come back:

• A cut edge under the glue, not a crushed one. Diamond on the rim shears the panel before the band is applied, so the joint is made on a cut surface.
• One change interval, not two. The pair is matched at 2 pcs, so the left and right cutter come off together and the edge stays symmetrical.
• Fitment checked in three numbers. 80 mm, 30 mm and H63 taken off your own unit catch a wrong size before the order leaves the counter.
• No lifting gear at the station. 2.84 kg per pair is a hand change for one fitter.
• Machines already on your floor. Listed for KDT, NANXING and Homag edge banding machines.
• A size outside the list is not a dead end. Customization is supported, quoted against your drawing or the bore and height you measure.
• A spare pair in the drawer. With a second pair on the shelf, an edge that goes dull mid-shift is a change at the station, not a wait for a regrind to come back.

80 mm outside diameter, 30 mm bore, 63 mm height and a 3+3Z tooth layout. Read the same callout off the cutter on your spindle before ordering, because a match on the rim alone does not confirm the bore.

Two. The order unit is 1 pair – 2 pcs, so both cutters on the premilling head are replaced together at the same interval.

It fits if your premilling unit takes an 80 mm cutter on a 30 mm bore with 63 mm of height. Measure the spindle seat with a caliper rather than a worn cutter, and check the height against the band you run.

KDT, NANXING and Homag edge banding machines are the ones named in the listing. The fitment check is still the three numbers — 80 mm, 30 mm, H63 — taken off your own premilling unit.

Neither: it is a premilling cutter. It runs at the premilling station ahead of the glue pot and takes the panel edge before the band goes on; rough trimming and fine trimming cutters are separate parts.

Yes. The listing names wood and plastic banding material for this premilling tool, and the PCD edge is the surface that meets both.

Yes. Customization is a listed service. Send the outside diameter, the bore and the height you need, or a drawing, and the quote comes back against those numbers instead of against a size name.

Quoted per pair — the listing carries contact-us-for-a-quote rather than a fixed figure. Send PMC004, the size and the quantity, and the price comes back on that enquiry; packing uses durable materials and international or express shipments carry a tracking code.