φ56*φ16*H14*4Z Rough Trimming Cutter For KTD Edge Banding Machine

Need to change a worn rough trimming cutter on a KTD edge bander without waiting weeks for the machine maker? EC001 goes on the same trim station on three measured numbers: 56 mm outside diameter, 16 mm bore and 14 mm height, with 4 teeth on the rim. It ships as 1 pair = 2 pcs, 0.31 kg per pair, so both cutters change in one order and the two sides of the station cut to the same depth. Size code: φ56*φ16*H14*4Z; price follows the quantity you ask for.

An edge bander stops paying for itself at the rough trim station in three familiar ways: a dull cutter starts leaving a chalk-white, fuzzy band instead of a clean cut, a wrong size code arrives after the machine has already been stripped down, and single cutters bought one at a time leave the two sides of the station cutting to different depths. The EC001 is made to remove all three.

It is a rough trimming cutter for KTD edge banding machines, listed as φ56*φ16*H14*4Z: 56 mm outside diameter, 16 mm bore, 14 mm height and 4 teeth. It is the first cutter the glued overhang meets at the trim station, so it takes the bulk of the band off before the fine trimmer squares the joint.

The cutter is sold as 1 pair = 2 pcs, and the pair weighs 0.31 kg. The two cutters wear at the same rate on the same pass, so buying the pair is what keeps the trim depth equal on both faces of the panel instead of one edge running part-worn.

It is listed for edge banding on wood and MDF, and customisation is supported when the size callout you need is off-list. Each pair travels in a cardboard box with foam inserts, sealed and labelled as the buyer requires, and the price is quoted on the quantity you order.

Four numbers, one tooth count and one unit decide the fitment and the cut — all of it read off the size code φ56*φ16*H14*4Z:

• 56 mm outer diameter — the rim that sets the cut circle, matched to the trim head a KTD edge bander already runs.
• 16 mm bore — the seat that centres the cutter on the trim spindle; measure it on the spindle, not on a worn cutter.
• 14 mm height — one setting covers a 14 mm band height, so the head is not shimmed between jobs.
• 4Z, four teeth — each tooth takes one quarter of the overhang per pass instead of the whole edge.
• 1 pair, 2 pcs — both sides of the trim station change in one order, at 0.31 kg for the pair.
• Rough trim stage — the first cut after the glue and pressure roller, taking the band down before fine trimming.
• Wood and MDF — listed for edge banding on wood and MDF panels, the two substrates most banding lines run.
• Customisation supported — an off-list size is quoted against your drawing or the dimensions you measure.
• Packed as a pair — cardboard box with foam inserts, sealed and labelled to the buyer's instruction.

The choice at the trim station is usually between an original cutter that takes weeks to arrive and a cheap one that does not fit — both cost machine time:

• Fits on three measured numbers. 56 mm, 16 mm and 14 mm are checked with a caliper before ordering, so a wrong size code is caught at the counter instead of at the machine.
• Both sides changed together. one order is 2 pcs, so neither side of the trim station is left running a part-worn cutter against a new one.
• Trim depth stays equal. a matched pair wearing at the same rate holds the cut on both panel faces to the same depth.
• Spare pair on the shelf. 0.31 kg for the pair means a spare set costs almost no cabinet space, and a change at the station is minutes rather than a stopped line.
• Reorder by part number. EC001 plus φ56*φ16*H14*4Z is all a repeat order needs, with no machine serial to look up.
• Off-list sizes handled. customisation is supported, so a size outside the list is quoted from a drawing rather than refused.
• Packed to travel. foam-cushioned cardboard, sealed and labelled per buyer, so the 4 cutting edges arrive as they left.

Check three numbers on your trim head: 56 mm outside diameter, 16 mm bore and 14 mm height. If those three match the size code φ56*φ16*H14*4Z, the cutter seats on the same spindle; measure the bore on the spindle seat itself, not on a worn cutter, because a worn part reads small.

A pair. Each unit is 1 pair = 2 pcs at 0.31 kg for the pair, which is how a trim station is normally changed — both cutters at once.

Four teeth. Z is the tooth count in the size callout, so 4Z means 4 cutting teeth on the 56 mm rim; the bore is 16 mm and the height 14 mm.

Rough trim. It takes the bulk of the glued overhang first; the fine trimmer and the scraper only touch the joint after this cutter has made its pass.

Yes. Customisation is supported, so an off-list size is quoted against your drawing or the three dimensions you measure — give diameter, bore, height and tooth count.

Wood and MDF. The listing names wood and MDF for edge banding work, which covers the two substrates most banding lines run.

In a cardboard box with foam inserts, sealed with heavy-duty packing tape and labelled with the buyer's own marking and destination. Shipping is by courier, so the pair leaves the box with its edges intact.

The price is quoted on the quantity you order, not fixed on the page. Send the item number EC001 together with the quantity, and the quotation comes back on that enquiry.