Pneumatic Flat Scraping Device For Edgebanding Machine Edgebander Parts

Need to take the glue line and the edge overhang off both faces of a panel at the machine instead of at the bench? This pneumatic flat scraping device is one set: an upper scraper and a lower scraper on the same body. It mounts on the aluminum profile rack, scrapes at a feed speed of 30 m/min, covers panels up to 60 mm thick, and each scraper carries 10 mm of adjustable stroke. The body is steel, L75 x W58 x H185 mm, 2.5 kg, painted or polished.

Three things keep a scraping station from running clean: a glue line that is still shiny after the trimming cutters because the scraper was set by eye, top and bottom faces scraped with two different settings, and a worn scraper that stops the line while someone hunts for a spare. This device takes all three off the operator.

It is a pneumatic flat scraping device for edgebanding machines, supplied as one set: an upper scraper and a lower scraper working on both faces of the panel after trimming. Each scraper carries 10 mm of adjustable stroke, so scraping depth follows the band instead of being guessed, and the pair runs at a feed speed of 30 m/min.

The unit covers panels up to 60 mm feed thickness, so the thickest board on the line still passes the scrapers. The body is steel, L75 x W58 x H185 mm, 2.5 kg, painted or polished, and specified to leave no damage on the panel faces it scrapes.

It fits the aluminum profile rack already on the machine, and the set ships with screws, tube and valves, so nothing has to be fabricated at the shop. OEM and ODM work is accepted, and the part is swapped as one set instead of rebuilt on the bench, which keeps a scraping station running through a shift change.

What the set is, where it goes, and what each number decides:

• One set, two scrapers - the set is an upper and a lower scraper, so both panel faces are scraped at one station.
• 10 mm adjustable stroke - each scraper adjusts through 10 mm, so depth is set to the band, not to the last panel.
• Pneumatic drive - the device is pneumatically actuated, and the set includes the tube and valves that feed it.
• 30 m/min feed speed - the scraper works at the speed the line already runs, 30 m/min, without slowing it.
• 60 mm maximum feed thickness - one unit covers board up to 60 mm, so the thickest panel on the line still runs through it.
• L75 x W58 x H185 mm body - the size is measurable against the rack before the order is placed.
• 2.5 kg complete set - the net weight is 2.5 kg, so the load on the rack is known in advance.
• Steel, painted or polished - the body is steel, with painting or polishing as the surface treatment.
• Aluminum profile rack mounting - the installation location is the machine's aluminum profile rack, the rail the station already uses.
• No damage on panels - the scrapers are specified to leave the panel face clean while they take the glue line off.

The alternatives today are scraping by hand with a blade held at an angle, or pulling the station apart to reset it. This device is the third option.

• Both faces in one setup. One set carries the upper and the lower scraper, so the panel is not turned between passes and the two depths stay matched.
• The depth becomes a number. 10 mm of adjustable stroke on each scraper means the second shift starts where the first one finished.
• It does not slow the line. 30 m/min is the feed speed the scraping station already runs at, so the machine keeps its cycle.
• One unit for the board you buy. Panels up to 60 mm feed thickness run through the same device, so one part covers the range.
• A swap, not a fabrication job. The set mounts on the aluminum profile rack and arrives with screws, tube and valves.
• Known weight, known size. 2.5 kg and L75 x W58 x H185 mm can be checked against the machine with a tape measure before ordering.
• The glue line leaves, the face stays. The part is specified as no damage on panels, so what comes off is adhesive, not board.

An upper scraper and a lower scraper. One set is both of them, and it ships with screws, tube and valves, so the pneumatic connection comes with the part.

Up to 60 mm feed thickness. Anything the line runs, from a thin panel up to 60 mm, passes through the same set, so one unit covers the whole range.

10 mm per scraper, upper and lower. The depth is set on the scraper itself rather than on the machine frame, so the two faces can be brought to the same setting.

On the aluminum profile rack. That is the stated installation location for the part, and the screws for it are part of the set.

30 m/min. That is the rated feed speed of the device, so it suits a line already running at that speed rather than asking the machine to slow down.

Yes - it is a pneumatic device, and the tube and valves are included in the set. Working air pressure is not stated in the data for this part, so send your machine model and the air line details with the enquiry if you are fitting it to a new station.

No. The part is specified as no damage on panels, and each scraper is set through 10 mm of stroke so it takes the glue line without cutting into the board.

Yes - OEM and ODM are both acceptable. Send the machine make, the rack position and the panel thickness you run; the price is quoted per order, so this listing carries no fixed price.