Black Cast Iron Trimming Knife Manual Trimmer Cutter Woodworking Machinery Tools

Trimming PVC, ABS or melamine edge tape by hand usually means a flexible utility blade, a slip that gouges the panel face, and an edge that changes with whoever holds the knife. This trimmer scraper removes that variable. A 120 x 60 x 20 mm black painted metal body holds the blade in a slot with a single cross-head screw, so the edge sits where the slot puts it, not where your wrist puts it. One hand, no setup, no power. Reorder part 40213814.

A shop that trims edge tape by hand hits the same three problems: a utility-knife blade that flexes and digs into the panel face, an edge that comes out different depending on who held the knife, and a stop in production every time a blade goes dull. This manual trimmer scraper takes all three off the table.

The tool is a 120 x 60 x 20 mm black painted metal body with a rectangular opening cut through the top face. The blade sits inside that opening and is clamped by a single cross-head screw, so its cutting edge is set by the slot in the body rather than by how steady your wrist is. The body carries the load; the blade only shaves.

It is built around the three edge materials that come off a bander most often, PVC, ABS and melamine, and it is meant for the passes after banding: the tape that stands proud of the panel, the glue smear at the joint, the small lip at a panel end.

The numbers to buy against: 120 mm long, 60 mm wide, 20 mm thick, black, metal, painted finish. It is a hand tool for a bench or a fitter's bag, priced per order, and the same part number covers all three edge materials, so the drawer holds one item instead of three.

Eight things decide whether a hand trimmer gets used every day or ends up in a drawer.

• Palm-length body - 120 mm long, 60 mm wide, 20 mm thick, so it closes inside a hand with the blade clear of your knuckles.
• One-screw blade clamp - a single cross-head screw holds the blade in place, so setting the edge and releasing the blade use the same fastener.
• Recessed blade slot - the cutting edge sits in an opening cut through the top face, and that slot is what keeps depth repeatable from panel to panel.
• Painted metal body - material metal, finish painting, colour black, so glue residue lifts off with a cloth instead of soaking in.
• Three edge materials - PVC, ABS and melamine tape are the materials this scraper is specified for.
• Nothing to plug in - a purely manual tool, so it works at the bander, at the bench or on a fitted cabinet.
• Flat reference face - the 60 x 120 mm underside rides on the panel, so the tool registers on the board rather than on your eye.
• Replaceable blade - when the edge wears, the blade comes out and the 120 mm body stays in service.
• Reorder by number - part 40213814 is the exact item on this page, not a family photo of one.

The choice on a small shop floor is usually between sending edges out and doing them with a knife. This is the third option.

• The edge stops depending on who trimmed it. A blade held in a milled slot cuts the same line on the first panel and on the hundredth, so a new hire produces the same edge as the fitter who trained them.
• Outsourcing becomes optional. Edges that used to travel to a sharpening or trimming service become a pass at the bench instead of a van trip.
• Blade depth is a setting, not a skill. One screw sets it, the 20 mm body and its slot hold it, and the next operator inherits your setting.
• No bench real estate. 120 x 60 x 20 mm goes in a toolbag: no fixture, no stand, no footprint on a bench that is already full.
• Spend on blades, not on bodies. The body is metal with a painted finish; when the cutting edge goes, the blade is released by the same single screw.
• Works away from the bander. Assembled cabinets, on-site touch-ups and the last panel before a break are all inside a hand tool's reach, where a machine trim station is not.

PVC, ABS and melamine. Those three are the materials the scraper is specified for, which covers the tape that comes off most edge banders in a panel shop.

It is 120 mm long, 60 mm wide and 20 mm thick. That puts the whole body inside a closed hand while the blade sits in the top-face slot, clear of your knuckles.

You set it. The blade is clamped by a single cross-head screw in a slot cut through the 20 mm body, so releasing the screw lets you reset the edge and locking it holds that position.

The blade comes out. It is held by the same one screw, so it can be released, sharpened or replaced while the 120 mm body stays on the bench.

No. It is a purely manual tool with no motor, no air line and no clamp, so it can be used at the bander, at the bench or on a cabinet that is already installed.

No. It takes over where the machine stops. The edge still has to be banded first; the scraper handles the tape that stands proud, the glue line and the lip at a panel end.

Order by the part number 40213814. The photo, the 120 x 60 x 20 mm size and the colour are all tied to that number, so a reorder is the same tool.

Ask for a quote against 40213814. Tell us how many pieces and which edge material you run, and the figure comes back against that quantity.