4014030041 4-014-03-0041 Scraping Blade Edgebanding Machine Tools Radius Scraper Edgebander Inserts 20*12*2mm Carbide scraping insert

Will it fit? Only if four numbers match: 20 mm long, 12 mm wide, 2 mm thick, 4 mm inner hole. This is the carbide scraping insert that scrapes the glue line off a panel edge after the trimming cutters, and it is ground to a radius - R1.5, R2 or R3. Both 4014030041 and 4-014-03-0041 are the same insert, listed for Homag, CEHISA, SCM and Brandt CNC edge banding machines. Measure the insert you are removing before you order.

Three things go wrong at the scraping station: the glue line still looks glossy because the insert's radius no longer matches the profile, the replacement arrives in the wrong size because it was ordered from the sticker instead of the parts list, and the line sits waiting on a 2 mm piece of carbide. This insert settles all three.

It is a scraping knife insert - the blade that scrapes the remaining glue and edge residue off the panel after the trimming cutters have cut the band to length. The body is 20 mm long, 12 mm wide and 2 mm thick, it carries a 4 mm inner hole that locates it in the holder, and the edge is ground to a radius so it follows the rounded corner of the edge instead of stepping it.

Two numbers, 4014030041 and 4-014-03-0041, resolve to the same insert, so a parts list and a machine sticker both work as an order reference. R1.5, R2 and R3 profiles are all available under that one number, which keeps three edge profiles on one spares line instead of three.

It is listed for Homag, CEHISA, SCM and Brandt CNC edge banding machines. Measure the insert you are removing against those four numbers and the order is settled before it ships - a scraping edge is a consumable, swapped rather than re-ground on the bench.

What the four numbers decide, and what the part actually does:

• 20 x 12 x 2 mm body - 20 mm long, 12 mm across, 2 mm thick: the three dimensions that must match the holder before anything else is checked.
• 4 mm inner hole - a 4 mm bore through the 2 mm body locates the insert in its holder, so it is a mounted part, not a clamped flat blade.
• Three radii under one number - R1.5, R2 and R3 are all available under 4014030041, so three edge profiles need one spares code.
• Radius ground edge - the profile is a radius, so the insert follows the rounded corner of the edge instead of cutting a flat step into it.
• Carbide cutting edge - the edge is carbide, the material named on the part, so a 2 mm insert scrapes adhesive and edge residue rather than slicing the panel face.
• Two numbers, one insert - 4014030041 and 4-014-03-0041 are the same part, whichever number the parts list shows.
• Four machine families - listed for Homag, CEHISA, SCM and Brandt CNC edge banding machines, so a mixed-brand line carries one insert.
• Works after the trimming cutters - the insert scrapes at the station downstream of trimming, which is why its edge is ground, not serrated.

Two bad options, and where this insert sits between them: running a dull radius until the edge needs hand sanding, or holding three different codes for three profiles.

• A dull scraping edge becomes a swap, not a shutdown. The insert is 2 mm thick and located by one 4 mm bore, so the station is back in production the moment the spare is on the shelf.
• The glue line stops being a hand-finishing job. The radius on the insert follows the 20 mm length of the scraping edge, so the residue left by the trimming cutters is taken off at the machine.
• Three profiles, one code to remember. R1.5, R2 and R3 all live under 4014030041, which means one part number covers the whole radius family on the shelf.
• Four numbers settle the fit. 20 x 12 x 2 mm plus a 4 mm inner hole is the entire fit decision, so a caliper and a parts list are enough to order without a photo exchange.
• One insert across a mixed-brand line. Homag, CEHISA, SCM and Brandt machines are all on the listing, so a plant running four brands keeps one spares code instead of four.
• Order by the number you already have. 4014030041 and 4-014-03-0041 both point to this insert, so the maintenance log and the machine sticker no longer need to agree before the order goes out.

Check four numbers first: 20 mm long, 12 mm wide, 2 mm thick and a 4 mm inner hole. If those match the insert you are removing, it fits - the part is listed for Homag, CEHISA, SCM and Brandt CNC edge banding machines.

Yes. The two numbers describe one part, so either the parts-list form 4-014-03-0041 or the compact form 4014030041 can be used to place the order.

Match the radius to the edge profile you are scraping, and all three are available. The radius is the only variable in the order, because length, width, thickness and the 4 mm hole stay at 20 x 12 x 2 mm.

No. Trimming cutters cut the band to length; this insert scrapes the remaining glue and edge residue off afterwards, which is why its edge is a ground radius on a 2 mm body.

Carbide. The part is specified as a carbide scraping insert, so the 20 x 12 x 2 mm body carries a carbide edge rather than a coated steel one.

Homag, CEHISA, SCM and Brandt CNC edge banding machines. The listing covers those four families, and the fit is still confirmed by the 20 x 12 x 2 mm dimensions and the 4 mm hole.

Yes. R1.5, R2 and R3 are all available under the same part number, so the radius and the quantity are simply stated per line when the order is placed.

The price is quoted per order, so ask for a quote with the radius and the quantity you need. Dimensions and the part number are fixed, but this listing carries no published price list.