Pheumatic Control PUR Glue Pot With Dust Removal Function - Edgebander Part

Replacing a worn glue pot on an edgebander should not change the way the line glues. The XEIQD-B pneumatic control PUR glue pot runs PUR and EVA, melts in 10-15 min, draws 2 kW, and uses a 1.0 fine coated mesh knurling on the glue roller to carry a thin, even film instead of a flooded one. A dust removal function clears chips at the glue line before the band is pressed on. It ships as a spare part for woodworking edgebanding machines, manual version also available.

A shop running an edgebander hits the same three things on the glue line: the pot lays on more adhesive than the joint needs, so part of an expensive glue is scraped off; dust and chips from trimming sit on the panel edge, and the band lifts weeks later; and every pot change is a fresh setup, with the film set by feel instead of by a number. The XEIQD-B removes all three.

It is a pneumatic control PUR glue pot with a built-in dust removal function, a spare part for woodworking edgebanding machines. What changes the glue line is the roller face: a 1.0 fine coated mesh knurling that carries a metered film rather than a flooded one — that is where the glue saving and the even gluing come from. The dust removal function clears loose particles before the band is pressed on.

Control is pneumatic, so the glue feed is switched by air rather than by an operator leaning over a hot pot. From cold, the pot reaches a workable melt in 10-15 min; the unit draws 2 kW.

The same pot runs PUR and EVA adhesive, so one spare covers the moisture-resistant and the standard interior jobs on the line. A manual version is available for stations with no air. It packs in a standard carton box.

What the glue line does comes down to these details, each with its figure.

• 1.0 fine coated mesh knurling — the roller face is a 1.0 coated mesh pattern, so it carries a thin, even film, not a flooded one.
• Dust removal built in — the pot clears loose chips at the glue line before the band is pressed on.
• Pneumatic control — glue feed is switched by air, so the film holds across a shift instead of being re-feathered by hand.
• Glue saving — a metered film leaves less squeeze-out at the pressure roller, so the glue stays in the pot.
• Precise gluing — the mesh meters the adhesive, so film thickness repeats panel after panel on the same setting.
• 10-15 min melt — from cold, the adhesive reaches a workable melt in 10-15 min, so a pot change fits a shift change.
• PUR and EVA — 2 adhesive families on one pot: PUR for moisture- and heat-resistant joints, EVA for interior work.
• 2 kW input — the unit is rated at 2 kW, the figure to match against the glue station it replaces.
• Manual version available — for a station with no air line, the same pot comes with 1 lever and no air requirement.
• Standard carton box — 1 pot per carton, so it stores flat on the spare parts shelf.

On the glue line the choice is usually one of two: keep buying pots at the maker's price, or run the bander with a film nobody can repeat. This pot is the third option.

• Stop paying for glue you scrape off. a metered film from the 1.0 mesh knurling leaves less squeeze-out at the pressure roller, so the adhesive that used to end up as scrap stays in the pot.
• Fewer lifted bands from chips. the dust removal function clears particles at the glue line, so the joint closes on wood rather than on debris.
• Set the film once, not every shift. pneumatic control holds the feed at the valve setting, so the next operator inherits a number instead of a feel.
• One spare covers two adhesive jobs. PUR and EVA both run on the same pot, which means 1 spare on the shelf instead of two.
• Back on the line in 10-15 min. that melt window is short enough to fit between two shifts, so a failed pot does not cost a production day.
• A fit for stations without air. the manual version keeps the same body for a line with no compressed air, so the spare still goes in the machine.

Both PUR and EVA. The pot is built for those two adhesive families, so one spare covers moisture-resistant joints and standard interior work.

10-15 min. Once it reaches the melt, the adhesive is workable and the pneumatic feed can be set at the valve.

Yes for the pneumatic version, which is the standard mode of action. A manual version is available for a station with no air line.

It cleans the glue line. Loose dust and chips are cleared before the band is pressed on, so the adhesive bonds to wood instead of to debris.

It meters the adhesive. The coated mesh pattern on the glue roller carries a thin, even film, which is where the glue saving and the repeatable gluing come from.

2 kW. That is the rated figure for the unit, and it is the number to match against the glue station being replaced.

Check the glue station mount and the feed connection on your own machine before ordering. The pot is a spare part for woodworking edgebanding machines, and the machine side differs by model.

Packing is a standard carton box, and MOQ and lead time are fixed together with your quote. Price is quoted per order, so the terms follow the quantity you ask for.