Cutter Head 100x30xH55 15Z Premilling Cutter For Homag Edgebander Cutting Tool

A worn premilling head shows up as a torn panel edge and banding that lifts at the seam; a head with the wrong bore will not seat at all. This WhisperCut cutter head is 100 x 30 x H55 mm — 100 mm outer diameter, 30 mm inner hole, H55 head height, 15Z (15 cutting edges) — listed for Homag edgebanding machines. Those three numbers are the whole fitment check. Price on request.

A dull premilling head on an edgebander does not announce itself. It shows up as a panel edge that reaches the glue pot torn instead of square, as banding that bridges that tear and lifts a few weeks later, and as an operator sanding edges by hand at the end of the line. A head with the wrong bore is worse than a dull one: it will not seat on the arbor at all.

This is a 100 x 30 x H55 mm premilling cutter head for edgebanding machines, catalogued under the WhisperCut designation. 100 mm outer diameter, 30 mm inner hole, H55 head height, 15Z — 15 cutting edges on the head.

It mounts on a 30 mm arbor at the pre-milling station and cuts the panel edge before the banding goes on. The edge is squared and the torn fibre is cleared, so the banding meets a clean face and bonds across its full width instead of bridging a torn surface. The 100 mm disc covers that edge in one pass.

Fitment is settled with three numbers before anything is ordered — 100 mm outer, 30 mm bore, H55 height — and the head is listed for Homag edgebanding machines. Matching those three numbers to the arbor in front of you is the whole check. Price is on request from Shunhongyu.

What decides whether a premilling head cuts the edge square or merely rubs it:

• 100 mm outer diameter. The disc measures 100 mm across, the size the pre-milling station is listed to take.
• 30 mm inner hole. The bore is 30 mm, the mounting size of the head; an arbor of another diameter needs a different head, not a shim.
• H55 head height. H55 in the size string is the head height, the figure that sets how much of the panel edge the head reaches.
• 15Z cutting edges. 15 edges around the 100 mm circumference share the cut, so each edge takes a shallow bite per revolution.
• Premilling, not trimming. It cuts before the banding goes on; fine trimming and end trimming are separate heads used after.
• Listed for Homag edgebanders. The head is catalogued for Homag edgebanding machines, so fitment comes down to the three sizes.
• WhisperCut geometry. The catalogue describes the WhisperCut head as the quiet-running version of this 100 mm disc; no decibel figure is published.
• One string to reorder. 100 x 30 x H55 with 15Z identifies the head completely, so a repeat order is a copy of the first line, not a new drawing.
• Price on request. The quote follows the quantity on your enquiry.

When a premilling head dulls, the usual choice is a cheaper head of unknown size, a hand-sanded edge, or waiting on the machine maker. What this head changes:

• Fitment is decided before the order. 100 mm outer, 30 mm bore, H55 height — three numbers that either match your arbor or do not, so the wrong part is caught on paper.
• The banding meets a cut edge. Pre-milling strips the torn fibre the glue would otherwise bridge, which is what keeps the banding down at the seam.
• Fifteen edges share the work. 15Z spreads the cut over 15 edges, so one edge is never asked to carry the whole pass on its own.
• No adapter, no shim. A 30 mm bore seats on a 30 mm arbor; anything else is the wrong head, and you find that out in minutes instead of after a run.
• Reorder from one line. 100 x 30 x H55 / 15Z identifies the head completely, so the second order is a copy of the first.
• One station, one head. It is listed for the pre-milling position on Homag edgebanding machines, not borrowed from a trimming station.
• The price follows your quantity. A quote on request is priced for the quantity and destination you actually order, not a single-piece list figure.

100 x 30 x H55 mm, with 15Z on the head. 100 mm is the outer diameter, 30 mm is the inner hole and H55 is the head height; those three numbers are what an order is checked against.

Yes, if that machine takes a 30 mm arbor. The head is listed for Homag edgebanding machines and mounts on a 30 mm inner hole, so measure the arbor before ordering — another arbor size needs another head.

The diameter. 100 mm is the outer diameter of the disc; the height is H55 in the size string, and 30 mm is the inner hole.

15 cutting edges on the head. Z is the tooth count in tooling sizes, so 15Z means 15 edges are cut around the 100 mm circumference.

Premilling. It cuts the panel edge before the banding is applied; fine trimming and end trimming are separate heads used after the banding is on.

A squared, clean edge. The head removes torn fibre instead of pressing it flat, so the banding bonds across its full width rather than bridging a torn surface.

Yes, if that machine takes a 100 mm disc on a 30 mm arbor at H55. Fitment is by those three numbers; the model name on the machine does not change the bore.

Send the size string 100 x 30 x H55 / 15Z and the quantity you need. Price is quoted on request rather than listed, so the figure you get matches the order you place.