Red Ball Manual Edge Trimmer Woodworking Machine Tool Edge Trimming Cutter

Need to trim edge banding or scrape film flush without sending panels out? This is a manual edge trimmer: a red ball handled film scraping knife with a 90 × 55 mm cutting head and a net weight of 0.76 kg. The metal parts are stainless steel with a chrome finish, the handle is red plastic, and it comes in a standard carton box from China. Trims wood, plastic and film edging by hand. Series STS401 - 408.

Any bench that fits edge banding or laminate film runs into the same three things: the band sits proud of the panel and has to come down flush without gouging the face, a knife that slips leaves a step you can feel with a fingertip, and a tool that needs two hands slows the bench down. The STS401 - 408 trimmer closes those three gaps.

This is a manual edge trimming cutter: a red ball handled film scraping knife for trimming and polishing the edges of wood, plastic and similar panel materials. The head measures 90 × 55 mm and the tool weighs 0.76 kg, light enough to steer one-handed along a panel edge and heavy enough to stay steady through the cut. The metal parts are stainless steel with a chrome finish; the handle is red plastic.

The cut is made by hand, so there is no wheel to dress and no fence to re-square between panel thicknesses: you lay the head on the panel and pull along the edge. That makes it a practical companion to the sliding table saw or edgebander on the floor, where the machine applies the band and the hand tool finishes the joint.

Each unit ships as a woodworking machine spare part in a standard carton box, origin China, in series STS401 through STS408.

What you get on the bench, in numbers:

• Red ball handle — a bright red plastic handle marks the tool on a crowded bench and gives a full-palm grip on the 90 × 55 mm body.
• 90 × 55 mm head — a compact footprint that still reaches between a proud band and the panel face on narrow edges.
• 0.76 kg net weight — light enough to steer one-handed along a panel, heavy enough not to chatter in the cut.
• Chrome-finished metal parts — stainless steel with a chrome finish, so film and glue residue wipes off instead of building up.
• Film scraping knife — ground for scraping film and trimming edging, bringing a proud band down flush to the panel.
• Wood and plastic — one head covers solid wood edges, MDF edges and plastic edge banding.
• No setup between panels — nothing to plug in and no fence to re-square, so going from thin film to a 2 mm band is a change of hand pressure.
• Spare-part format — supplied as an individual replacement unit, so a dulled trimmer is swapped off the shelf without a service call.
• Standard carton packing, origin China — each unit is packed in a standard carton box.
• STS401 - 408 series — eight part numbers, one 90 × 55 mm body, one red handle.

For a small shop the choice is usually between sending panels out and doing the edge by hand. This tool is for the second path, done properly:

• One head instead of two tools. The same 90 × 55 mm cutter scrapes film and trims banding, so a bench that carried a scraper and a trimmer carries one 0.76 kg tool.
• The finish stops being a queue. Work ends when the band is flush, not when an outside shop returns the panel.
• A steadier angle, fewer re-cuts. The full-palm red ball handle holds the head at the same angle along the edge, which keeps a trimmed band from stepping.
• Low cost of ownership. No motor, no blade wheel, no coolant: a dulled unit is simply replaced as a spare part.
• Easy to shelve. The STS401 - 408 series ships in a standard carton box, so the full part number set fits on one shelf.
• Works with the machines you have. It finishes what a sliding table saw or edgebander starts, adding a finishing step instead of a new machine.
• Clean metal, quick wipe-down. Stainless steel with a chrome finish sheds film and glue residue, so the tool keeps its edge instead of gumming up.

It trims and scrapes panel edges by hand. The head scrapes film and cuts proud edge banding flush to the panel face on wood, plastic and similar panel materials, then leaves the edge ready to wipe down.

90 × 55 mm and 0.76 kg. The compact body still reaches between a proud band and the panel face on narrow edges, and the 0.76 kg mass keeps the cut steady without tiring your wrist.

A hand tool. It is a manual edge trimmer: you set the head on the panel and pull along the edge, so there is no motor, no blade wheel and no fence to adjust.

Wood, plastic and film-type edging. Solid wood edges, MDF edges and plastic edge banding are all finished with the same head, which is why one tool covers a mixed batch.

Stainless steel, with a chrome finish, on a red plastic handle. The chrome layer is what lets glue and film residue wipe off instead of curing onto the working metal.

No. Depth of cut is set by hand pressure, so one cutter covers thin film and thicker banding; the STS401 - 408 series covers the part numbers you stock.

A standard carton box, from China. Each unit is packed in a standard carton, and shipping is arranged to the buyer's requirements.

Yes. It is a finishing tool for the same bench: the machine applies the band, then the trimmer finishes the joint by hand where the machine head cannot reach.