Woodworking Manual Edge Trimmer Edge Scraper Edge Banding Trimmer

Need to trim edge banding flush on a straight panel without a bench machine? The Blue-001 does it by hand in one pass. It takes edge strip 0–40 mm wide and banding under 0.5 mm thick, and the whole tool is 130 × 80 × 70 mm and 160 g, so it lives in a pocket. Blue engineering-plastic body with a matte surface, a replaceable white steel blade, spare blades in the box. No power, no air line, no setup.

A shop that bands edges by hand on site hits the same three things: the overhang comes off with a chisel or a knife and gouges the panel face, a dull blade tears PVC instead of shaving it, and nothing fixes the depth, so no two panels come out the same. The Blue-001 is built for those three.

The Blue-001 is a hand-held trimmer and scraper for edge banding strip: it takes strip 0–40 mm wide and banding under 0.5 mm thick. The blade sits tilted against the panel face rather than flat on it, so the overhang is shaved off at the joint line and the board face is left alone.

The body is 130 × 80 × 70 mm and weighs 160 g, moulded in blue engineering plastic with a matte surface that hides handling marks. The blade is white steel, held by two screws, and the cutting plane is fixed by the body itself, so trim depth does not drift from panel to panel.

It is used on paint-free board and straight-line plates, with bendable melamine and PVC banding. A screwdriver takes the blade out, a spare set comes with the tool, and a white steel blade can be re-polished and refitted. One hand tool replaces the file, the knife and the second pass.

What the dimensions and the blade geometry do on a panel edge:

• Blade tilt design — the blade meets the banding at an angle instead of lying flat, so it shaves the overhang at the joint line and never runs across the face.
• 0–40 mm strip width — one body covers the strip widths used on standard panels, from narrow PVC banding up to 40 mm wide material.
• Banding under 0.5 mm — the thickness the blade is set for; 0.5 mm and thinner shaves clean, thicker banding belongs on a machine trimmer.
• 130 × 80 × 70 mm, 160 g — one hand, one pocket, and no bench space taken when panels are already stacked.
• Blue engineering-plastic body — moulded matte, so it takes knocks at the panel stack without showing every mark.
• White steel blade — high hardness at the cutting edge, and it can be re-polished and reused rather than replaced.
• Two screws hold the blade — a screwdriver is the only tool needed to take it out or replace it.
• Spare blades supplied — a set ships with the trimmer, so a dulled edge does not stop a run.
• Trim, then scrape — the same body takes the overhang off and then cleans the trimmed edge.
• Straight-line panels — paint-free board, straight-line plates, bendable melamine and PVC banding.

The usual choice is a bench trimmer you do not own, or a knife that marks the panel. This tool sits between the two.

• Trimming without a bench machine. The trimmer is 160 g and runs on hand pressure, so a panel that is already on the stack is trimmed where it lies.
• The overhang goes, the face stays. The blade meets the banding at an angle, so the cut stops at the joint line instead of running across the melamine.
• The same edge on every panel. Depth is set by the body of the tool rather than by wrist pressure, so a second operator reproduces what the first one did.
• The blade is the only consumable. White steel, two screws, and it can be re-polished and refitted; a spare set ships with the tool.
• 0–40 mm covers the stack. One trimmer handles every strip width on standard panels, so no second body is needed when a wider band turns up.
• Small enough to keep at the edge bander. At 130 × 80 × 70 mm it fits a toolbox drawer, so touch-up after machine trimming happens at the machine, not across the shop.
• Matte surface, blue body. The finish does not polish up or show handling wear over a shift, which matters for a tool that is picked up and put down hundreds of times.

Under 0.5 mm. That is the banding thickness the blade is set for; thicker banding needs a machine trimmer with a powered cutter.

0 to 40 mm. The throat takes strip up to 40 mm wide, so one tool covers the banding used on standard panels.

No. It is made for straight-line work: straight-line plates, paint-free board and bendable melamine or PVC banding along a straight edge.

Yes. The blade is held by two screws and comes out with a screwdriver, so a replacement is done at the bench.

Yes. A set of spare blades is supplied with the tool, so a dull edge does not stop a run.

Paint-free board and straight-line plates, banded with bendable melamine or PVC strip. It shaves the overhang; it is not a panel saw.

Yes. The white steel blade can be polished and refitted, so it is reused rather than thrown away.

Ask us for the current price. Send the strip width and banding thickness you run and we quote the trimmer with its spare blade set.