58x16xH12x4Z Fine Trimming Cutters For Edge Banding Machine Woodworking Tools

A dull fine trim cutter should not cost you a head rebuild. This EC113 cutter is one TCT disc measuring 58 mm outer diameter, 16 mm bore and 12 mm high, with 4 teeth for the fine trim station of a woodworking edge banding machine. Tungsten carbide edges hold their shape against glued PVC, ABS and melamine tape, and 4 teeth put an edge past the work every 90°. Radius options R1.5 / R2 / R3, plus custom sizes, are available to order.

Three things go wrong at the fine trim station. A dull cutter glazes the glue line instead of cutting it, so panels leave a white haze. A disc with the wrong bore or height sits off centre and leaves a step at the top of the edge. A spent edge pushed too far chips the melamine face. The 58X16XH12X4Z disc is aimed at all three.

It is a TCT fine trimming cutter for a woodworking edge banding machine, supplied as a spare disc, not a complete head. The disc measures 58 mm outer diameter, 16 mm bore and 12 mm height, carries 4 teeth (4Z) and weighs 0.24 kg. The cutting edges are tungsten carbide, because they meet glued PVC, ABS and melamine tape while the glue is still hard. Radius versions R1.5, R2 and R3 are available, and other sizes are produced to order.

Four teeth put an edge past the work every 90°, so the gullet between them is wide and trim waste clears instead of packing against the tape. The sharpened, ground body keeps all four teeth tracking one circle, so a trimmed edge stays straight along the panel length.

Fitting is a measuring job: check the old cutter against 58 / 16 / 12 mm, then confirm spindle direction and tooth count. Used on woodworking edge banding machines, including Homag machines.

What decides whether this cutter fits, and how it behaves in the cut.

• 58 mm outer diameter — the trimmed edge is cut on a 58 mm disc, so measure the old cutter before ordering.
• 16 mm bore, 12 mm height — these two numbers decide whether the disc sits square on the spindle shoulder.
• 4 teeth (4Z) — one cutting edge every 90° of rotation, with a wide gullet that clears trim waste.
• TCT tungsten carbide edges — carbide meets glued PVC, ABS and melamine tape without rounding over mid-shift.
• Sharpened, ground body — all 4 teeth are ground to track one circle, so a trimmed edge stays straight.
• 0.24 kg disc — light enough to swap by hand at the spindle, with no lifting gear on the trim station.
• Radius versions R1.5 / R2 / R3 — three rounded profiles on the same body; state the radius when ordering.
• Fine trim duty — built for the station that removes the thin overhang and glue line, not the bulk of the tape.
• Spare disc, not a new head — you replace one cutter; the spindle, bearing and trim adjustment stay as they are.
• Sizes made to order — other diameters, bores, heights and tooth counts are produced on request.

At the trim station the choice is usually between sending the head out for sharpening and running a dull disc until the next shutdown. A 0.24 kg replaceable disc shortens both.

• Back to cutting with one disc. A dull edge is swapped out as a single 58 mm cutter, so the spindle and the adjustment you already trusted stay untouched.
• Edge quality you can ship. 4 teeth on a 58 mm body keep the chip and the heat small enough that chipped melamine and fuzzy PVC do not reach the customer.
• Wear sits where the cutting is. Carbide edges on a steel body put the expensive material on the cutting edge, so abrasion is spent there and not across the whole disc.
• Fewer SKUs on the shelf. One 58 × 16 × 12 mm body with R1.5, R2 and R3 covers the rounded profiles most shops run, in 0.24 kg of stock per disc.
• No dead end on an older machine. Custom diameters, bores, heights and tooth counts are made to order, so an obsolete head size does not force a machine retrofit.
• Predictable trim, not a re-setup. Because this is a spare part with fixed 58 / 16 / 12 mm geometry, replacing it does not reopen the trim adjustment.

Any edge banding machine whose fine trim spindle takes a 58 × 16 × 12 mm disc with 4 teeth. Fit depends on those three dimensions plus tooth count and spindle direction, not on the machine badge, so measure the cutter you are removing.

Fine trim. It is the second station cutter that removes the thin overhang and glue line left behind by rough trimming, not the hogging cutter that takes off the bulk of the tape.

Only if the spindle and the trim setting are meant for 4Z. Four teeth take a larger chip per tooth than six at the same feed, so a 4Z disc belongs on a thin overhang at a moderate feed, not on a heavy hogging cut.

Tipped TCT. The cutting edges are tungsten carbide on a steel body, which keeps the 58 mm geometry stable while the carbide does the cutting.

Match the radius of the profile you are selling. All three are available on the same 58 × 16 × 12 mm body, so measure the cutter you are replacing before you choose.

It fits if the fine trim spindle takes a 58 × 16 × 12 mm 4Z disc. The cutter is used on woodworking edge banding machines including Homag machines, but the old disc — not the nameplate — is the measurement that decides.

When the edge stops cutting and starts polishing. A dull fine trim cutter burnishes the glue line, so the panel shows a white haze and the tape edge feels rounded instead of crisp.

Yes. Other diameters, bores, heights, tooth counts and radii are produced to order; send a drawing or the measured dimensions of the old cutter.