150mm Polishing Wheel For Hebrock Edgebanders High Gloss Finish

Changing a worn buffing wheel on a Hebrock edgebander should not cost a shift. The BW017 is a cotton polishing wheel, 150 mm outside diameter, 25 mm wide, with a 20 mm bore, so it drops straight onto the polish spindle of a Hebrock machine. Cotton burnishes the trimmed glue line to a high gloss instead of cutting into it. 50 pcs minimum, dispatch in 1-7 working days, every wheel bagged on its own inside a taped carton. The same family also covers 150x50 mm, 200x50 mm and 240x170 mm spindles.

Every edgebanding line loses gloss in the same place: the polish station. A wheel that has glazed over burnishes nothing, a wheel with a slack bore runs out of true and leaves chatter along the glue line, and a wheel that is not on the shelf stops the station for a shift. The BW017 cotton polishing wheel is built for that station on a Hebrock edgebander, and it closes all three gaps.

It is a 150 mm outside diameter disc, 25 mm across the face, bored 20 mm through the centre. The face is cotton cloth, the finer of the two common buffing media: cotton burnishes, sisal cuts, so the wheel pulls the trimmed PVC or veneer edge to gloss instead of scraping it. The 20 mm bore seats on the polish spindle in one push and comes off in one pull, which keeps a changeover down to a minute.

One wheel handles the polish station itself; the rest of the line is covered in the same family - 150x50 mm, 200x50 mm and 240x170 mm - so a workshop running two edgebanders holds one spares box instead of four part numbers.

Ordering is counted in pcs: MOQ 50 pcs, T/T payment, dispatch in 1-7 working days from a supply of 100,000 pcs a month, each wheel in its own plastic bag inside a taped cardboard carton.

What separates it from a generic 150 mm buffing disc:

• Hebrock spindle fit - 150 mm diameter, 25 mm face, 20 mm bore, sized for the polish station of a Hebrock edgebander.
• Cotton cloth face - the softer of the two buffing media, so it burnishes the glue line to gloss instead of cutting it back.
• Finishes after the trimmer - takes the edge once the trimmer and scraper have made their pass, on wood and plastic.
• One-push changeover - a bored 20 mm centre goes on and off the spindle by hand, no puller, no shims, no adapter.
• Four sizes off one shelf - 150x25x20 mm as the standard, plus 150x50 mm, 200x50 mm and 240x170 mm.
• Full-face contact - 25 mm of face width lets the operator work the wheel across the panel edge without the corner digging in.
• Bagged one by one - each wheel travels in its own plastic bag, then a sturdy taped carton, so faces arrive clean and square.
• Consumable economics - MOQ 50 pcs with the unit price negotiated on quantity, payment by T/T.
• Stock depth behind it - 100,000 pcs a month supply and dispatch in 1-7 working days.
• Same carton as the service kit - feed rollers, pressure rollers, glue pot heaters, end cutters and trimmers ship from the same spares desk, so one order covers one service.

The usual choice is between the edgebander maker's spare-part price and running a glazed wheel until the gloss disappears. This wheel is the third option.

• The line keeps running. A 50 pcs box means the next changeover is a walk to the shelf, not a purchase order.
• Gloss where the buyer looks. On a cabinet door the edge is what a hand runs along, and a 150 mm cotton wheel puts the shine there in one pass.
• No fitting kit. 150 mm diameter, 25 mm face, 20 mm bore: the bore is the mounting, so a fitter is not needed to swap a consumable.
• One supplier for four sizes. 150x25x20 mm, 150x50 mm, 200x50 mm and 240x170 mm on the same sheet, the same T/T terms and the same carton.
• Cost sits in the right line. A 50 pcs minimum with a negotiated unit price keeps the spend in consumables instead of capital spares.
• Dispatch you can plan around. 1-7 working days out of 100,000 pcs a month, so a distributor and a single-shift shop order the same way, and neither has to carry a year of stock.

Yes, if the polish station takes a 150 mm wheel with a 25 mm face and a 20 mm bore - that is the BW017 format. Check the three numbers against your spindle nose before ordering, especially on a machine that has been rebuilt.

It is sized for Hebrock edgebanders. On any other make, the decision still comes down to the same three numbers: 150 mm outside diameter, 25 mm face width, 20 mm bore.

Cotton. Sisal is the coarser medium and takes material off the edge; cotton burnishes the trimmed glue line to gloss, which is what the polish station is there for.

No. Every wheel ships bare and bagged on its own, so compound stays a separate choice on your side of the line.

150x50 mm, 200x50 mm and 240x170 mm, alongside the 150x25x20 mm standard. All four come from the same spares desk.

50 pcs, price to be negotiated on quantity, dispatch in 1-7 working days. Payment is T/T and monthly supply is 100,000 pcs.

One wheel per plastic bag, all bags inside a sturdy cardboard carton, sealed with packing tape - the bag keeps the cotton face clean and the carton keeps it round.

Shunhongyu. The same spares desk also supplies feed rollers, pressure rollers, glue pot heaters, end cutters and top and bottom trimmers.