Edgebanding Buffing Wheel 180x50x20 Edgebander Machine Replacement Parts

Need the buffing wheel that actually slides onto your edgebander polishing shaft? The BW013 is a cotton buffing wheel at φ180 × φ50 × 20 mm — 180 mm outside diameter, 50 mm center hole, 20 mm face width — packed in a carton box and listed as a woodworking edge banding machine replacement part for various edge banding machine models. The 50 mm bore is what decides fit, so measure the shaft before you order. Other sizes and other center hole shapes are also provided.

A worn buffing wheel announces itself on the panel, not on the wheel: the edge leaves the polishing station cloudy, the gloss stops matching the approved sample, and the last station sets the pace for the line. Then a replacement arrives with a bore that will not go onto the spindle. The BW013 carries its three dimensions on the part.

This is a cotton buffing wheel for the polishing station of a woodworking edge banding machine: outside diameter φ180 mm, center hole φ50 mm, face width 20 mm, body in cotton cloth. It is listed as a replacement part compatible with various edge banding machine models, so the φ50 mm bore — not the badge on your machine — decides fit.

Bores and face widths are where a mixed shop gets caught, so this wheel is also provided in other sizes and other center hole shapes on request. It ships in a carton box, keeping loose grit out of the cloth, and it is a consumable reordered by number rather than by drawing.

The edgebander runs its abrasives in sequence and this wheel is the last to touch the panel. A full 180 mm diameter and 20 mm face back on that station recovers the edge the customer already signed off, with machine, glue and board unchanged.

What the part is, in the order a buyer checks it:

• 180 mm outside diameter — the wheel measures φ180 mm across, so the polishing station is set against a number you can check with a rule.
• φ50 mm center bore — a 50 mm hole. This is the fit check: it will not seat on a smaller spindle, and cloth cannot be reamed out.
• 20 mm face width — the cloth face that touches the edge is 20 mm wide, and 20 mm is the overall thickness.
• Uncombed cotton body — built from uncombed cotton cloth, the material listed for this part rather than a bonded abrasive disc.
• Replacement-part category — sold as a woodworking edge banding machine replacement part, ordered by measurement rather than by serial number.
• Wide model fit — listed as compatible with various edge banding machine models; the shaft measurement, not the badge, decides.
• Other sizes on request — polishing wheels in diameters and thicknesses other than φ180 × 20 mm are also provided.
• Other bore shapes on request — bores that are not the plain round φ50 mm are also provided, so a keyed shaft stays a part question.
• Carton box packing — every wheel ships in a carton box, keeping the cotton face clear of workshop grit in transit.

Ordering a polishing wheel ends one of two ways: keep running the cloudy edge and hope nobody looks, or buy a part you cannot dimension and send it back when the bore is wrong. BW013 reduces that to three measurements.

• Three numbers replace a drawing. 180 mm across, 50 mm through the middle, 20 mm thick. Anyone in the shop can check the old wheel against those three numbers in under a minute.
• The bore is published, not implied. A 50 mm center hole is stated on the part, so you avoid the return caused by a wheel that never fitted.
• Bought as a wear part. Cloth polishes by contact and wears out by contact, so ordering it as a dimensioned replacement keeps the decision on the part.
• One dimension set across a mixed fleet. If two edgebanders share a polishing shaft, the same φ180 × φ50 × 20 mm wheel serves both, and one spare covers both.
• An odd spindle stays a part problem. Other sizes and other center hole shapes are provided, so a non-round shaft does not turn a 20 mm wear item into a machine change.
• Edge appearance stops drifting. With a full 20 mm cloth face on the station, today's gloss starts from the same contact width as last week's approved sample.

Yes, if your polishing shaft takes a φ50 mm hole and the wheel position is built around φ180 mm. Those two numbers, plus the 20 mm face, are the whole fit check — the machine brand is not part of it.

Measure the old wheel: outside diameter, hole diameter, face thickness. Compare with 180 mm, 50 mm, 20 mm. If the old wheel is already in the bin, measure the shaft diameter and the gap between the flanges instead.

Cotton cloth. BW013 is listed as an uncombed cotton buffing wheel, and the cotton face is the part that contacts the edge — there is no abrasive grit bonded into it.

Yes. Other sizes of polishing wheel and other center hole shapes are also provided. Send the outside diameter, the thickness and the hole size you need, and the shape of the bore if it is not plain round.

A buffing wheel. It mounts on the polishing station of a woodworking edge banding machine and is catalogued as replacement tooling, not as a cutting wheel that removes material.

Woodworking edge banding machines. The part is listed as compatible with various edge banding machine models, and because fit is set by the shaft, one wheel can cover more than one maker.

In a carton box. The cotton face reaches you without loose grit pressed into it, which matters because grit in the cloth is what puts a scratch in a finished edge.

A photo of the old wheel plus its three measurements — 180 / 50 / 20 style numbers — and the machine model. If the bore is not plain round, add the hole shape and the shaft diameter.