14.6x11.6x2 CEHISA Kantenanleimmaschine Hartmetall-Abstreifer für Kantenanleimen

Dull scraping insert leaving a glue line on every panel? This one drops into the existing seat: 14.6 × 11.6 × 2 mm body, 35° working land, one centre hole, supplied in left- and right-hand versions. Solid carbide, 10 pcs per box, listed for CEHISA edge banding machines and for SCM and Brandt CNC edge banding machines that take the same insert. Quote the part number 14.6×11.62-35°-R with your machine model and quantity for a price; custom sizes are quoted on request.

A shop running an edgebander meets the same three problems at the scraping station: one worn insert leaves a glue line down the whole panel, a dulled corner means chasing a scraper unit because the insert alone is hard to source, and left and right hands get mixed up, so one edge is scraped and the other left as trimmed.

Part 14.6×11.6×2-35° is a solid carbide scraping insert for CEHISA edge banding machines. The body is 14.6 mm long, 11.62 mm wide and 2 mm thick, with a 35° land ground on the working end and a stepped relief behind it. One hole on the centreline takes the bolt already on the seat.

Direction matters as much as size. The insert is supplied in left-hand and right-hand versions, so both sides of a two-insert station are re-bladed from one box. Four numbers decide fit — 14.6, 11.62, 2 and 35° — and all four sit in the part number 14.6×11.62-35°-R.

Inserts ship 10 pcs per package, one per compartment, so a matched pair and the spares behind it arrive with their edges intact. OEM and custom sizes are supported where the standard footprint does not match your seat. Price is quoted against the model and quantity you send.

Four numbers and one hand suffix decide whether an insert drops into a CEHISA scraping unit.

• CEHISA-Fußabdruck — 14.6 × 11.6 mm body, 2 mm thick, one hole on the centreline, seated with the existing bolt.
• 35° Arbeitskante — the angle is ground on the end of the insert, not set on the scraper body.
• Linke und rechte Hände — both directions are made, so a two-insert station is re-bladed from one box.
• Stufenrelief hinter der Kante — the working end is machined back, so the 35° land cuts and the body behind stays clear.
• Massiver Hartkörperschaft — 2 mm of ground carbide in one piece, a consumable insert rather than a brazed blade.
• 10 Stück pro Karton — one insert per compartment, so ten pieces travel as one sealed box.
• Maschinenabdeckung — CEHISA edge banding machines, plus SCM and Brandt CNC units that take the same 14.6 × 11.6 × 2 mm insert.
• Ein Bolzen pro Position — a dulled corner is swapped without disturbing the scraper body behind it.
• OEM und kundenspezifische Größen — send length, width, thickness, angle and hand, and the part is ground to that drawing.
• Wiederholbare Teilenummer — 14.6×11.62-35°-R carries length, width, angle and hand, so a reorder repeats the first order.

The scraping station is a consumable position, not a machine. These are the numbers that keep it cutting.

• Ein Einsatz, nicht eine Einheit. A dulled corner is a 14.6 × 11.6 × 2 mm part on the purchase order, not a scraper unit.
• Beide Hände in einer Schachtel. Left and right travel together, so a re-blade never stops at half a station waiting for the other direction.
• Eine Nachbestellung, die sich wiederholt. The part number holds 14.6, 11.62, 2 and 35°, so the second order arrives with the first order's geometry.
• Wechsel gemessen in Bolzen. One fixing per insert, so a full station is re-bladed without dismantling the unit.
• Ersatzteile, die die Reise überstehen. 10 pcs per box, one insert per compartment, so cutting edges never touch another part.
• Ein Lagerartikel für die gesamte Linie. The same insert covers CEHISA and the SCM and Brandt units using the 14.6 × 11.6 × 2 mm seat.
• Passform vor dem Kauf geprüft. Measure the old insert against 14.6, 11.62 and 2 mm, or send a photo of the seat.
• Kundenspezifische Geometrie auf Anfrage. OEM and customisation cover sizes and angles outside the standard footprint, quoted from your drawing.

Yes, provided your scraper seat takes the 14.6 × 11.6 × 2 mm insert with the 35° land. Check the numbers on the old insert or on the part list of the scraping unit; if they read 14.6, 11.62 and 2 mm, this part is the match. Send a photo of the seat and the machine model if the numbers are worn off and the hand will be confirmed for you.

Buy both. The insert is made in left- and right-hand versions, and a scraping unit that carries two inserts normally holds one of each, so ordering a single direction leaves one side of the station unbladed. The hand is the last character of the part number, 14.6×11.62-35°-R.

Ten. Each package holds 10 pcs, one insert per compartment, so a matched pair plus eight spares arrives as a single box and the cutting edges stay separated in transit.

It is the hand marker in the part number. The insert is supplied in left- and right-hand versions, so quote the full code 14.6×11.62-35°-R when you order and state which hand you need for each seat.

35° is the angle ground on the working end, and that angle sets how the scraping edge meets the panel. Because the land is ground into the insert itself, the angle comes with the part; nothing on the scraper body is reset or re-machined when you change it.

Yes, where the seat takes the same 14.6 × 11.6 × 2 mm insert. The listing covers CEHISA edge banding machines and SCM and Brandt CNC edge banding machines using this insert, so the size check is the only step that changes between brands.

Yes. OEM and customisation are supported: send the length, width, thickness, angle and hand, or a drawing of the old insert, and the part is quoted against it. Mixed hands and mixed sizes can be quoted in one reply.

Send the part number and the quantity you need and a price is quoted against it. State the machine model and how many left-hand and right-hand inserts you want, so the quote covers the full station rather than a single seat.