Woodworking Power Feeder Parts Steel Gear Wheel Woodworking Feeding Machine Parts

Need to replace a worn gear wheel in a power feeder and do not want to buy the wrong size? This listing is the wheel itself, offered by tooth count: 12T Short, 12T Tall, 16T-1, 21T, 22T and 25T, all in steel. The bore is 15 mm on every toothed size shown, overall diameter runs 39.5 mm, 45.5 mm and 53 mm on the photographed sizes, and the parts carry the codes 27A-1, 06H-2, 12G-1 and 35A-1. Condition new, packed in a carton box.

Three things go wrong when a power feeder gear wheel is ordered by guess. The tooth count is taken from the machine model instead of from the failed part. The bore and keyway are assumed to match the last repair. The part arrives in a size the feeder never used, and the machine stays down for another week.

This listing is the gear wheel itself, offered by tooth count so the decision is made on the part in your hand. It carries drive between the gearbox and the feed rollers of a woodworking feeding machine, and it is steel. Six sizes are listed: 12T Short, 12T Tall, 16T-1, 21T, 22T and 25T. The two 12T versions share a tooth count but not a body; the Tall one carries a 26.5 mm boss standing 20.5 mm high.

On the photographed sizes, overall diameter is 39.5 mm on the 12T Tall, 45.5 mm on the 21T and 53 mm on the 25T, with a 15 mm bore throughout; the 16T-1 is a 10 mm plate. The same photos carry the codes 27A-1, 06H-2, 12G-1 and 35A-1.

Condition is new, and each gear wheel is packed in a carton box. Origin is Guangdong Province, China. Price is quoted per size and quantity, so send the tooth count, the bore and a photo of the old wheel.

What the six sizes change, and what stays the same:

• Six tooth counts — 12T Short, 12T Tall, 16T-1, 21T, 22T and 25T are listed separately, so the replacement is ordered by the count on the failed wheel.
• Steel body — the wheel is steel, which is the material listed for every size in this range.
• 15 mm keyed bore — each toothed size photographed is bored 15 mm, with a keyway cut so the key carries the drive.
• Bossed 12T Tall — 26.5 mm boss diameter and 20.5 mm boss height separate it from the flat 12T Short.
• Thin 16T-1 plate — 10 mm thick, the thinnest of the sizes photographed.
• Size codes on the parts — 27A-1 on the 12T Tall, 06H-2 on the 16T-1, 12G-1 on the 21T and 35A-1 on the 25T give a second way to check a size.
• Planer and jointer feeders — listed for woodworking feeding machines, including the feeders run on planers and jointers.
• New condition — supplied new, so the teeth are not run in and the bore is not oval.
• Carton box packing — each wheel ships in its own carton box from Guangdong Province, China.
• Other sizes on request — counts outside the six are quoted against a sample or a measured old part.

What the buyer gets when the spare is ordered on numbers instead of on a machine model:

• A part you can measure before you pay. Tooth count, bore and overall diameter are all on this page, so the wheel is checked against the old one across three numbers instead of one.
• One size, one order. Six counts are listed separately, and a 12T is not offered as a stand-in for a 16T.
• A steel wheel, not a gearbox. When a tooth wears, the wheel is the part that leaves the feeder, and the gearbox stays bolted to the machine.
• The keyed bore takes the load. Drive passes through the keyway in the 15 mm bore, so the shaft is not carrying the torque on its fit alone.
• Fewer re-repairs. A wheel matched on count, bore and diameter goes on once; a wheel bought on machine brand alone comes back out.
• Kept as a spare, not a project. The wheel is small enough to sit on the shelf in its carton box, so a worn tooth does not stop a shift.
• Quoted per size. Ask for 21T and the quote is for 21T, with the other counts priced on request.
• One enquiry for the whole range. 12T Short through 25T are ordered together, which matters to a shop running four feeders on the same floor.

Match the tooth count, the bore and the overall diameter against the old wheel. On the photographed sizes the bore is 15 mm and the outside diameter runs from 39.5 mm to 53 mm, so three numbers settle the size where the machine brand does not. Send a photo of the old wheel if any of the three cannot be measured.

The tooth count is the same; the body is not. 12T Tall carries a 26.5 mm boss that stands 20.5 mm high, while 12T Short is the flat version, so the one that fits is decided by the space left behind the wheel in the gear train.

No. Tooth count sets the drive ratio, so a 25T in place of a 22T changes the feed speed and the working diameter, and the two sizes do not interchange.

15 mm on every toothed size shown in the size photos. The bore is keyed, so the key takes the drive and the shaft fit alone is not asked to hold it.

Woodworking power feeders, including the units run on planers and jointers. They are listed as woodworking machinery accessories, not as a general gear.

Steel. Every size in this listing is in steel; the copper gear wheels are a separate listing and are not part of this range.

New. The condition listed for these gear wheels is new, so the teeth arrive unworn and the bore is not oval from an old shaft.

Carton box, with other dimensions quoted on request. Send the tooth count, the bore, the overall diameter and a photo of the old wheel, and the size is matched before the quote is issued.