Four Sided Planer Moulder Polyurethane Feeding Roll 120x30x30mm

Need a feed roller that grips the timber without marking it? The 54040116 polyurethane feeding roll fits four sided planers and moulders on a 30 mm shaft. Outside diameter 120 mm, face width 30 mm, bore 30 mm, with a high-strength steel core and a polyurethane (PU) working face that deflects around the board and springs back. It is sold as a replacement or OEM part, customization is supported on bore, width and hardness, and it ships by FedEx, DHL or UPS. Price is by quotation.

Moulders lose output in three places: a feed roll that has glazed over, so timber slips on the last pass; a roll that presses marks into a face the sander then has to clean up; and a machine idle while a replacement part crosses an ocean.

The 54040116 is a D=120mm, W=30mm, bore=30mm polyurethane feed roller for four-sided planers and moulders. A high-strength steel core carries the bore and holds the running diameter true; a PU tyre bonded to that core is the working surface. The metal keeps the geometry, the PU takes the contact.

Polyurethane gives three things at this size: high elasticity, so the roll recovers after every board instead of flat-spotting; abrasion resistance, so the face keeps its shape over repeated shifts; and grip, so the board is driven forward rather than skidded. Feed arrives smooth and vibration-free, which is what a four-sided finish depends on.

It is supplied as a replacement or OEM part for four sided planer moulder feed stations running a 30 mm shaft, measuring 120 x 30 x 30 mm overall. Customization is supported on bore, width and hardness; shipment is by FedEx, DHL or UPS from China.

Two things decide whether a feed roller works: the fit on the shaft, and the working face.

• 120 mm outside diameter — the running diameter the feed station is set for, so the pressure setting is unchanged.
• 30 mm bore, 30 mm face — slides onto a 30 mm shaft and matches the 30 mm roll width on four sided moulder feed stations.
• Steel core, PU tyre — a 120 mm high-strength steel hub with a bonded polyurethane outer layer, so load and grip are separate materials.
• Non-marking working face — PU deforms around the surface it drives and springs back, so planed faces leave without pressure marks.
• Abrasion-resistant surface — the PU face resists the wear that continuous board contact puts on a 120 mm roll.
• Even pressure across the width — elasticity keeps contact pressure uniform across the full 30 mm band, so no edge steers the board.
• Built for four sided planers — specified as a feeding roller for four sided planer stations on a 30 mm shaft, not a general purpose wheel.
• Replacement or OEM part — supplied to the 120 x 30 x 30 mm envelope of the roller it replaces, so no modification to the station is needed.
• Custom bore, width and hardness — customization is supported, so a 25 mm bore or a wider 50 mm face is quoted against your drawing.

The choice on a worn feed roll is narrow: run it until it marks the timber, or take the machine out of service and wait for a part. Both cost more than the roller.

• Replace the roller, not the feed unit. The part that wears is the 30 mm PU face, not the shaft, so one roller restores the station.
• A finish the sander does not have to rescue. A PU face that deforms and recovers leaves no pressure mark, which keeps sanding passes off faces already cut at size.
• Grip where output is lost. Slippage on the last pass becomes a step in the profile and a rejected board; a 120 mm PU contact face removes the slip, not the symptom.
• One part number on the shelf. A 120 x 30 x 30 mm roller is a single spare-parts line instead of a machine down while a courier is booked.
• OEM geometry, open channel. It is sold as a replacement or OEM part, so you buy the same envelope without a machine builder's catalogue and price list.
• Custom sizes without a tooling project. Bore, width and hardness are customization options, so a non-standard shaft becomes a quotation item, not a redesign.

Check three numbers first: outside diameter 120 mm, face width 30 mm, bore 30 mm. If your feed station runs a 30 mm shaft and a 30 mm wide roll, the 54040116 drops in without modifying the machine.

Polyurethane. The working face is a PU layer bonded to a high-strength steel core, which is why the part is listed as a polyurethane feeding roll rather than a rubber wheel.

Because the grip comes from elastic deformation, not from surface softness alone. PU presses around the timber and returns, so contact is maintained across the full 30 mm face for the life of the roll.

No marks at normal feed pressure. The PU face deforms around the workpiece and recovers, so it drives the board without the hard contact that presses a mark into a planed surface.

Yes, customization is supported. Send the bore, the face width and the outside diameter you need, and the roll is quoted to that drawing instead of to the stock 120 x 30 x 30 mm size.

Price comes by quotation, because it depends on the quantity and on whether the size is standard or custom. Send the three dimensions and the quantity you need, and you get a firm figure back.

By FedEx, DHL or UPS. The roller is exported from China, and the exact service level and transit days are confirmed together with the quotation.

It is supplied as a replacement or OEM part to the 120 x 30 x 30 mm envelope, so it occupies the same position on the feed shaft as the roller it replaces.