Manual Glue Pot For KDT Edgebanding Machine - Woodworking Edgebander Glue Tank

A dry edge band on a KDT line is usually the glue tank, not the operator. XEISD-B is that tank: the manual glue pot for KDT edgebanding machines, controlled by a hand lever with no control board in the chain. It comes as one assembly with the outlet block, heater cover, cable with plug and bracket. A pneumatic version is available, this model has 0 dust-removal parts, and glue pot spares are stocked separately. Price per inquiry; ships by DHL, FedEx or UPS.

A glue tank that stops feeding mid-shift costs three things at once: a panel banded with a dry edge, an operator finishing that run by hand, and a replacement that has to match a machine nobody measured. Ordering faster fixes none of the three. Ordering the right pot fixes all of them.

XEISD-B is the manual glue pot for KDT edgebanding machines, the edgebander glue tank that sits in the gluing unit and feeds the glue roller. Control is a hand lever with a rubber boot on the pot body, and the outlet block is worked by 2 ball-knob levers at the nozzle, so there is no controller screen in the chain. It arrives as 1 assembly: pot body, hand lever, perforated heater cover, pre-wired cable with plug, and a bolted bracket with slotted holes.

A pneumatic version is available where the line actuates the pot itself. This model is supplied without dust removal, 0 extraction parts, so a shop that already runs a hood on the edgebander is not sold a second one.

The pot is produced in China for KDT machines. Price is quoted per inquiry because manual and pneumatic are priced apart. One pot ships by DHL, FedEx or UPS, and glue pot spares are stocked separately, so a worn lever does not force a second complete pot.

Every line below can be checked against the pot on your machine:

• Hand lever, no control board — 1 lever with a rubber boot opens and closes the glue outlet, so there is no screen to read and no setting lost after a power cycle.
• Two ball-knob levers at the outlet — the glue block is worked by hand from 2 points, right where the glue leaves the pot and meets the roller.
• Perforated heater cover — 1 vented cover sits over the hot face with the cable run kept outside it.
• Pre-wired cable and plug — the harness leaves the cover as 1 lead with a plug, so the pot connects to the existing lead instead of being re-terminated on site.
• Bolted bracket with slotted holes — the plate bolts to the gluing unit and the slots absorb alignment without redrilling the machine.
• No dust removal built in — 0 extraction parts ship with this model; it is the pot, not a hood.
• Pneumatic version for actuated lines — the same pot family, worked by the line instead of by the operator's hand, quoted separately.
• Spares kept separate — levers, glue shafts and pot spares are orderable without buying a complete pot again.
• Made for KDT gluing units — bracket pattern and lever position follow the glue pot mounting on KDT edge banding machines.

Glue pot orders usually fail on one of two points: the pot does not match the machine, or the whole assembly has to be rebuilt from single parts. XEISD-B closes both:

• The control version is in the part number. Manual or pneumatic is the first thing to get wrong, and the hand lever pot carries its own item number, XEISD-B, so the order and the machine agree.
• One fit instead of a parts hunt. pot body, hand lever, heater cover, cable with plug and bracket arrive as 1 assembly, so the unit goes back together in one visit.
• No hood paid for twice. 0 extraction parts are included, so a ducted line buys the glue tank only.
• Feed set where the glue leaves. the lever sits on the body and 2 ball-knobs sit at the outlet block, so flow is trimmed at the nozzle instead of at arm's length.
• A repair, not a second pot. glue pot spares are stocked separately, so a worn lever is 1 line item, not a complete pot.
• It moves as a parcel. DHL, FedEx and UPS are all used, so one pot needs no forwarder and no pallet.

Yes. It is listed for KDT edge banding machines — the bracket is the part to check. Compare the mounting plate and the lever position on your old pot with the photos before ordering.

Manual. XEISD-B is the hand lever glue pot; the pneumatic version is also available for lines that actuate the pot themselves, and it is quoted apart.

No. This model ships without dust removal, 0 extraction parts, so it pairs with the hood already on the edgebander.

One complete pot assembly. Pot body, hand lever with rubber boot, 2 outlet ball-knobs, perforated heater cover, pre-wired cable with plug and the bolted mounting bracket.

Yes. Glue pot spares are stocked separately, so one worn part does not mean a second complete pot; ask for the pot spares list.

By hand, at two places. The lever on the pot body opens and closes the outlet, and the 2 ball-knob levers at the outlet block trim flow at the nozzle.

Quoted per inquiry — manual and pneumatic are priced apart. Send the KDT machine model and the quantity for a price.

Three things: machine model, a photo of the old pot's bracket and lever, and the quantity. With those the version and the fit can be confirmed in one reply.