Dual Tank Pneumatic Glue Pot With Dust Removal Function - Reverse Direction

Replacing a glue pot on an edgebander that runs two glues and cannot afford a glue line full of dust? The XEIQD-B is a pneumatic, dual tank glue pot built in the reverse direction, with a Teflon inner wall layer and a built-in dust removal function. Two tanks let a shop change between two glue types or colours without draining and cleaning the pot first. It is supplied in 4 build combinations - pneumatic or manual control, dual or single tank. A forward direction body and a glue pot for Homag edgebanders are also available.

A shop running an edgebander hits three problems with the glue pot: one tank means draining, cleaning and refilling before a colour change; dust and chips reach the gluing area and turn up as specks under the banding; and the pot that arrives does not match the machine, because direction and control type were not checked. The XEIQD-B is built to remove all three.

It is a pneumatic glue pot supplied as a spare part for edgebanding machines, built in the reverse direction. The body carries 2 tanks instead of 1, so a second glue type or colour is already loaded when the job changes. The Teflon inner wall layer keeps adhesive from baking onto the wall. The dust removal function clears dust and debris from the glue application area before the banding goes down.

One part number covers 4 build combinations - pneumatic or manual control, dual or single tank - plus 2 directions, reverse and forward. A glue pot for Homag edgebanders is also available on the same page.

Fitment is confirmed from a photo: send pictures of the glue pot currently on your machine, and the tank, flange and direction are checked before a quote goes out. Valve insert, locating ring and gaskets are available as replacements. Price is quoted on request and shipping is to be negotiated.

What separates this pot from a single-tank replacement is the configuration, not the paint.

• Pneumatic control. Air drives the pot, so glue feed repeats from panel to panel; the manual version is available where no air line reaches the station.
• Two tanks, one body. 2 separate tanks hold two glue types or colours, so a changeover is a switch, not a drain, a clean and a refill.
• Dust removal function. Dust and debris are removed from the glue application area, keeping contamination out of the line where the banding is pressed on.
• Teflon inner wall layer. The wall the glue touches is Teflon, so adhesive releases instead of carbonising onto steel.
• Reverse direction build. The body is built for reverse-direction mounting; the forward version is available for machine layouts that need the other hand.
• 4 build combinations. Pneumatic or manual control, dual or single tank - pick the combination your machine already runs.
• 2 directions on one part number. Reverse and forward are both listed, so the wrong-hand pot is not a return.
• Homag version available. The same glue pot is offered for Homag edgebanders alongside the KDT fitment.
• Fitment checked from a photo. Send pictures of your existing pot; tank, flange and direction are compared before the pot ships.
• Wear parts on the same order. Valve insert, locating ring and gaskets are offered as replacements.

The usual choice is between a single-tank pot and a clean-down before every colour change, or a whole new gluing unit. The XEIQD-B is the third option: keep the machine, change the pot.

• One pot, two glues. 2 tanks mean the second colour is already loaded, so changeover stops being a drain, a clean and a refill in the middle of a run.
• Dust stops before the glue. The dust removal function works on the glue application area, so debris is not sealed under the banding and returned as a reject.
• Cleaning hours come back. A Teflon inner wall layer releases adhesive, so the wall is wiped at the end of a shift rather than chipped.
• The right hand, ordered once. Reverse or forward, pneumatic or manual - 4 combinations are matched against your photo before the pot ships.
• No second trip for consumables. Valve insert, locating ring and gaskets can travel on the same order as the pot.
• KDT and Homag layouts. A Homag glue pot is available next to the KDT fitment, so a mixed machine shop is not chasing two suppliers.
• One spare covers the line. 1 part number carries both control types and both tank types, so the shelf spare is not tied to a single machine.
• No guessing on cost. Price is quoted on request; shipping is negotiated, and freight you arrange is accepted.

Send pictures of the pot you are replacing before you order - that is how fitment is confirmed, not from the model name alone. We check the tank, the flange and the direction against your photo. If your layout is the other hand, the forward version is available instead.

Pneumatic. Air pressure drives the pot, and the manual version is available as an alternative for a gluing station with no air line.

No. Dual tank is the version on this page and a single tank version is available. Two tanks are for a shop that swaps between two glue types or colours during the week.

Yes. Reverse direction is the build on this page, and the forward version is available on the same part number. Tell us which hand the machine needs and it is checked with your photos.

Teflon. The inner wall layer is Teflon, so adhesive releases from the wall instead of baking onto bare steel between clean-downs.

It removes dust and debris from the glue application area. Less debris at the glue line means less contamination sealed under the banding, which is where specks and open joints come from.

A glue pot for Homag edgebanders is also available. Send photos of the Homag pot and the fitment is checked before a quote is issued.

Price is quoted on request - there is no fixed figure on this page. Shipping is to be negotiated: you can arrange your own forwarder, or we can propose a method. Send the machine details and the quantity you need for both.