Pheumatic Control PUR Glue Pot With Dust Removal Function - Reverse Direction

Need to run PUR on an edgebander without cleaning the gluing area between every panel? The XEIQD-B melts PUR or EVA in 10-15 min, meters the glue through a 1.0 fine coated mesh knurling roller, and pulls dust off the edge at the same time. Mode of action is pneumatic, with a manual version also available. Rated power 2 kW. Built as the reverse direction unit, for edgebanders where the standard hand will not fit. Shipped in a standard carton box.

A shop that runs PUR on an edgebander keeps hitting the same three problems: glue goes on too thick and the joint line shows, chips and dust sit on the panel edge before the glue lands, and every adhesive change costs a clean-out. The XEIQD-B removes all three.

It is a pneumatic control PUR glue pot supplied as a part for woodworking edgebanding machines, built in the reverse direction version. Adhesive is carried onto the panel by a 1.0 fine coated mesh knurling roller, which meters a thin, even film instead of a heavy bead: that is the glue saving and the precise gluing point, in one component.

Melt time is 10-15 min from cold, and the pot is listed for both PUR and EVA adhesive. Rated power is 2 kW. The pneumatic mode of action holds application pressure steady through a shift, so the coat does not creep thicker by late afternoon; a manual version is also available where a shop would rather set pressure by hand.

The dust removal function clears the gluing area ahead of the roller, so the bond sits on clean wood rather than on debris. The unit ships in a standard carton box and mounts as a replacement part, not a machine rebuild.

Ten points to check against your own edgebander before you order.

• 1.0 fine coated mesh knurling — the roller is a fine coated mesh pattern, so the film is metered onto the edge instead of flooding it.
• Glue saving — a metering roller carries less excess adhesive back into the pot: adhesive not bought, and not cleaned out.
• Precise gluing — coat thickness stays even along the panel, which keeps the joint line closed on thin edge and thick edge alike.
• Pneumatic mode of action — air pressure drives the applicator, so contact pressure repeats from the first panel to the last.
• Manual version available — the same pot is built with hand control where no air line reaches the gluing station.
• PUR and EVA — one pot covers both adhesive families listed for this unit, whatever the job type.
• 10-15 min melt — cold pot to usable glue in 10-15 min, which is a coffee, not half a shift.
• Dust removal function — chips and dust are cleared from the gluing area before the glue goes down.
• Reverse direction build — the opposite-hand version, for machine layouts where the standard direction will not fit.
• 2 kW rated power — 2 kW is the figure listed for this pot as fitted to the edgebander.

The usual choice is between sending a tired pot out for a rebuild and living with a coat that is too thick. The XEIQD-B is the third option: keep the machine, change the part.

• You stop paying for glue you throw away. A 1.0 fine coated mesh knurling roller meters the film, so a shop running PUR all day buys back the adhesive a flooded coat used to waste.
• Bond failures move down. Dust removal runs ahead of the glue, so the PUR meets clean wood rather than chips and dust; a joint that fails is a rework, and rework is the expensive part of edgebanding.
• One pot, two adhesives. PUR and EVA on the same unit means a shop that switches between job types does not buy, store and clean a second pot.
• Back in production in 10-15 min. Melt time is 10-15 min, so a pot swap at shift start does not push the first panel back by half a day.
• Fits the machine you already own. The reverse direction build is a spare part for woodworking edgebanding machines: mount it, do not rebuild the line.
• A setting that repeats. Pneumatic control, or the manual version where there is no air line, keeps the pressure you found on Monday the same on Friday.

Only if your machine takes the reverse direction version. The XEIQD-B is the opposite-hand build sold as a part for woodworking edgebanding machines, so match the direction of the pot you are replacing before ordering. Send the machine make and model and we will confirm.

10-15 min from a cold pot. That is the melting time listed for this unit, so warm-up at shift start is minutes rather than hours, and the first panel does not wait half a day.

Yes. The pot is listed for both PUR and EVA adhesive, so one unit covers both families and a shop that switches job types does not need a second pot.

Only for the pneumatic version. The manual version is also available and sets the glue by hand, so a shop without air at the gluing station can still use this pot.

It clears chips and dust from the gluing area before the glue lands. That is the whole scope of it: it is a function on the pot, working at the glue line, not a replacement for your plant extraction system.

The pot. 2 kW is the power figure listed for this glue pot, so size the supply for the part, not for a complete edgebander.

It is the roller surface, and it is what meters the glue. A fine coated mesh pattern at 1.0 carries a thin film instead of a heavy bead, which is where the glue saving and the precise gluing design points come from.

Standard carton box, with price on request. The pot ships in a standard carton box as a spare part for woodworking edgebanding machines; send the direction and your machine model with the enquiry and the quote comes back against that configuration.