KDT Edgebanding Machine Glue Pot Gate - Glue Door for KDT Edgebanders

Need the glue door on a KDT edge bander to close again? This is that part: the gate that starts and stops glue flow at the pot. It is 190 mm long, 28 mm wide, 16 mm on the gate diameter and 10 mm on the second diameter, weighs 0.25 kg per piece and is made of steel. It fits both directions, forward and reverse, so one item covers both mounting orientations. No part number is printed on the gate itself, so order against the three dimensions above. Price follows an inquiry.

A glue door that will not shut tight shows up as the same three things on an edge banding line: glue carries on running onto the panel after the band has already passed, so the band pulls a smear into the next operation; the line waits while someone tries to dress the old gate back into shape; and the worn part turns out to carry no readable number, so the replacement is ordered from a photo and arrives with the wrong diameter.

KDT Edgebanding Machine Glue Pot Gate is the gate, or glue door, that closes the glue outlet on the pot of a KDT edge bander. It measures 190 mm in length, 28 mm in width, 16 mm on the gate diameter and 10 mm on the second diameter, and it is built from steel.

The gate runs in both directions, forward and reverse, so one item number covers the two mounting orientations used on KDT glue pots, instead of a left-hand gate and a right-hand gate having to be ordered as two lines.

Weight is 0.25 kg per piece, light enough to be handled and changed at the pot without lifting gear. It is supplied as the gate on its own, unmarked or marked, and the price follows an inquiry rather than a list.

Every line below can be checked against the gate already on your pot:

• Forward and reverse — the gate is made for both directions of travel, so 2 mounting orientations are covered by one item instead of two part numbers.
• Steel construction — steel body, 0.25 kg per piece; a machined metal face seats against the glue outlet.
• 190 mm overall length — the gate measures 190 mm end to end, which is the length to check first when comparing it against the worn part.
• 28 mm body width — the gate is 28 mm across the body, the second number that has to match before the part is ordered.
• Two diameters in one profile — 16 mm main gate diameter against 10 mm on the second; the step seats the gate, not the length.
• Starts and stops the glue — the door at the pot outlet: open it and glue feeds, close it and flow stops.
• Marked or blank — supplied as a branded Shunhongyu gate or as an unmarked face, so the same part serves a machine that carries no badge.
• One spare, not one pot — the gate ships on its own; a worn door does not pull a whole pot into the order.
• Fits KDT edge banders — application is the glue pot of KDT edge banding machines, in furniture, cabinet and panel shops.

The real choice when a glue door wears out is between a line that keeps smearing glue until an agent ships a part, and a bench repair that lasts one shift. This gate shortens both waits:

• Three numbers settle the order. 190 mm long, 28 mm wide, 0.25 kg: the gate carries no readable number of its own, so the dimensions do the identifying that a label cannot.
• One item, both directions. forward and reverse are the same part, so 1 line is ordered and there is no left-hand gate to run out of stock on you.
• Steel, so it keeps its seat. the closing face is steel rather than a soft casting, which is what lets it keep shutting flat instead of being dressed back into shape every few weeks.
• Back to banding in one fit. 0.25 kg and a single gate means the swap is a pot-side job, done standing at the machine rather than stripping the assembly.
• No ghost part number. there is no code on the gate, so the listing names the dimensions instead of a figure nobody can read off the worn part.

KDT edge banding machines. It is the glue door at the outlet of the KDT glue pot, the part that opens and closes the glue flow, and it is supplied as a spare for machines already in service.

Yes, both. The gate is made for forward and reverse operation, so the two mounting orientations used on KDT glue pots are covered by the same item, and no handed version has to be ordered.

190 mm long, 28 mm wide, 16 mm on the gate diameter and 10 mm on the second diameter, at 0.25 kg per piece. Measure the gate you are replacing against those numbers before ordering.

Steel. The gate is a machined steel part, not a plastic or soft-cast door, which is why it holds its closing face at the glue outlet.

No. The gate is supplied on its own as a single spare, so a worn or stuck door does not pull a complete glue pot into the order.

Either way. It can be supplied as a Shunhongyu gate or with an unmarked back face, so a machine that carries no badge does not get one.

Send an inquiry. Price is quoted per order rather than listed, and the three dimensions above are enough to confirm the gate before a quote is written.

Match three numbers: 190 mm length, 28 mm width, 0.25 kg weight. If those three agree with the worn part, the 16 mm and 10 mm diameters follow, because they are the same profile.