KDT Edgebander Gluing Gear 25T Spares For KDT Woodworking Edgebander Glue Tank

A 25-tooth gear decides whether this part fits. This one is a gluing tank gear with 25 teeth, material metal, listed as a spare for KDT edgebanding machines and quoted under product ID 46233258. It sits in the glue tank and turns the adhesive feed, so a chipped or rounded tooth shows up as an uneven glue line rather than as a stopped machine. Count the teeth and check the keyed bore on the old gear before ordering. Price is quoted per order.

A dry edge line, a chipped tooth and one glue tank priced as an assembly are usually the same failure seen three ways. The glue film is blamed first, the gear comes out second, and by then nobody has counted its teeth, so the replacement is ordered on memory instead of on a number.

This is a gluing tank gear with 25 teeth, material metal, listed as a spare for KDT edgebanding machines. It sits inside the glue tank and turns the adhesive feed as the panel passes, which is what puts an even film on the edge. The count is 25 teeth and the product ID is 46233258.

Tooth count is the working number on a part this small. A 25-tooth gear turns its mating gear at one fixed ratio, so a different count changes that ratio and the amount of glue that reaches the edge with it. Only the 25-tooth count is published here; no diameter, bore size or module is given, so the count and the photos are what a buyer checks.

The photos show the part as it is handled: a 25-tooth rim, a hub with a single keyway cut into the bore, and tapped holes for set screws. Installation into the tank needs no specialised tooling. Price is quoted per order, and 46233258 is the number to quote.

What 25 teeth, a metal body and one ticket number settle before the gear goes back into the tank:

• 25 teeth — The published count, written as 25T in the product name and as Teeth Qty 25 in the parameter table.
• Gluing tank position — The product field reads gluing tank gear, which puts the part inside the tank rather than in the machine drive.
• Metal body — Metal is the material listed; no grade, hardness figure or coating is published, so none is claimed here.
• One keyway in the bore — The third photo shows a single keyway, so the gear is driven through the shaft key and not by friction alone.
• Tapped set screw points — The hub carries tapped holes, shown with set screws fitted, which hold the gear on its shaft.
• One machine family — Application reads spares for KDT edgebanding machines, so the fit claim stays on 1 machine family instead of a universal claim.
• Precision, listed as feature 1 — On a 25-tooth part precision means a fixed count, so wear shows as a chipped or rounded tooth rather than as a slow drift.
• Cost, listed as feature 2 — The second stated feature is cost effectiveness, and the repair it prices is 1 gear instead of 1 glue assembly.

Between quoting a whole glue tank and guessing a tooth count from memory, the choice is 1 part that carries its number on the page: 25 teeth, so the check happens before payment rather than after delivery.

• The count is on the page. 25 teeth is written down, so the old gear is counted at the bench before the order, not after the parcel is opened.
• One gear, not one tank. Product ID 46233258 prices the part inside the tank, so 1 chipped tooth stops costing a glue assembly.
• The tank is opened once. Installation into the tank needs no specialised tooling, so the fit is 1 session rather than 1 booked technician visit.
• The check runs on the photos. A keyed bore and a 25-tooth rim are both visible, so the part in hand is compared with the part in the photo before payment.
• The fit claim can be tested. Application names KDT edgebanding machines only, so the buyer checks 1 machine family instead of trusting a universal claim.
• Stock is 1 small part. A 25-tooth gear on the shelf covers the wear point, and 1 spare is cheaper to hold than 1 standby glue tank.

Match 25 teeth and the keyed bore before you order. The data lists the part as a spare for KDT edgebanding machines and gives 25 teeth, but names no model numbers, so count the teeth on the old gear and compare the third photo.

25. That is the only count in the product data, written as Teeth Qty 25 and carried in the product name as 25T.

Metal. Metal is the only material listed, and no grade, hardness figure or coating is published, so nothing narrower is claimed.

The gear. Product reads gluing tank gear and Type reads edgebanding machine parts, so this is the toothed part in the tank, not the tank.

No. Installation in the tank is described without specialised tooling or extended training, so a maintenance fitter can do the swap.

Then it is a different part. A 25-tooth gear drives its mating gear at one fixed ratio, so a different count changes the ratio and the glue film with it.

Price is quoted per order. Send product ID 46233258 with the count 25 teeth; no fixed price is published, so the figure arrives with the quotation.

Yes. The supplier lists woodworking machine parts beyond this gear, so other wear parts for the same machine are quoted in the same enquiry.