End Cutting Cushion Pad For KDT Edgebander KDT End Cutting Shock Absorbing Unit

Need the end cutting unit on your KDT edgebander to stop biting into the panel? This PU + Steel cushion pad sits in the KDT end cutting shock absorbing unit and takes the strike before the edge does. It is a replacement spare for KDT edge banding machines, supplied in various sizes matched to the measurement you send. Material: PU + Steel. Carrier: DHL, FedEx or UPS. Origin: China. Send the length, width and thickness in mm with a photo of the old pad, and the pad is quoted to that figure.

Three things go wrong at the end of the board on an edgebander. The end cutting unit strikes the panel and the corner chips. The worn pad behind it stops absorbing, so the stroke travels into the frame and the trim comes out ragged. And when the pad splits, the parts list only says various sizes, so nobody knows what to order.

It is the cushion pad that fills the KDT end cutting shock absorbing unit, between the cutting stroke and the machine body. It is built from PU + Steel: the PU side deforms and absorbs, the steel carries the mounting load so the pad holds position instead of creeping. It is a wear part, replaced rather than repaired.

There is no single number to order against. KDT end cutting assemblies are quoted in various sizes, so the pad is matched to your unit: send a photo of the old pad beside a ruler plus length, width and thickness in mm, and it is quoted to that figure.

Origin is China, shipment runs by DHL, FedEx or UPS, and the pad sits in the same KDT spare parts range as the end cutting parts around it. Price is quoted per size.

Nine points decide whether a pad like this fits and lasts, and all nine can be checked before you order.

• Two materials only — PU and steel: one side compresses on every stroke, one side carries the load, no third material in the part.
• Quoted to your measurement — length, width and thickness in mm come from your photo and your ruler, not from a catalogue line.
• Built for the KDT end cutting unit — it fills the shock absorbing position on KDT edge banding machines, the only application listed for it.
• A replacement, not a repair — one pad per worn position, fitted where the old pad came out, nothing else on the unit disturbed.
• Order from one photograph — a picture of the old pad on a ruler is enough for a quote: no drawing, no sample shipment.
• One range, not five suppliers — the pad sits with the end cutting parts for the same machine, so a shutdown list becomes one inquiry.
• Three carriers — DHL, FedEx or UPS, chosen by destination and confirmed on the quote.
• Ships from China — origin China; a single pad and a repeat order take the same route out.
• Stock it as a spare — the pad is a consumable, so one spare per machine costs less than a stopped line waiting on a courier.

Buyers of this pad choose between two bad options: run the end cutting unit until the edge quality collapses, or send the unit out and lose the line. The pad removes the choice for the price of one part.

• The chipped corner stops. A pad that still absorbs takes the strike before the panel does, so the trim leaves a clean corner instead of a torn one.
• Ordering stops being guesswork. You send millimetres and get millimetres back, with no matching against a list that only says various sizes.
• A short stop, not a rebuild. One pad is a single-part change in one position, so the unit stays on the machine and the line stays in place.
• Vibration stays at the unit. The strike is taken at the pad, so less of it reaches the frame, the trim station and the floor.
• The cutting edge stops taking the shock. Impact the pad absorbs is impact the knife no longer has to survive, so the edge is spent on cutting.
• Your line stays KDT-standard. The pad is made for KDT edge banding machines, so a replacement keeps the machine as it was built.
• One basket for the whole unit. Pad, end cutting parts and trimming parts come from one KDT spare parts range, in one shipment and one set of documents.

It absorbs the strike of the end cutting unit, so the impact stops at the pad instead of reaching the panel edge and the machine frame. It sits in the KDT end cutting shock absorbing unit and is the part that wears first.

Send a photo of the old pad lying next to a ruler, plus length, width and thickness in mm. This item is offered in various sizes rather than one fixed number, so the measurement is the whole of the order.

PU plus steel, and those two materials are the complete listed build for this part. The PU face is the side that compresses on each stroke; the steel carries the mounting load so the pad keeps its position.

No. It is listed as a KDT edge banding machine spare, so fit is quoted against a KDT end cutting unit, not against another brand's trimming station.

Order one pad for every worn position you find. A panel is trimmed at both ends, so check each shock absorbing position on the unit and count them before the order goes out.

Yes. The pad belongs to a KDT spare parts range that also covers the end cutting and trimming parts around it, so one inquiry can carry the whole list.

By DHL, FedEx or UPS, whichever suits the destination address. Origin is China, and the carrier is confirmed together with the quote.

The price is quoted per size, so there is no single figure to publish. Send the measurement and the quantity, and the quote comes back against exactly that.