Edgebanding Cutting Blade For KDT Woodworking Edge Banding Machine

Cutting edge banding and need the blade that does it? The EC043 is the replacement cutting knife for KDT woodworking edge banding machines, listed in three sizes: 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm, all in alloy. Each blade is one plate on its own locating hole, so a dull edge is a part to swap, not a cutting unit. Send the size and the quantity and the price is quoted per order.

A dull cutting blade on an edge bander does not announce itself. Three things show up instead: the banded end leaves the station ragged and has to be trimmed by hand, the cut stops landing square panel after panel, and the line waits while somebody looks for a spare. All three come back to the blade, not to the cutting head.

The EC043 is the replacement cutting blade for the edgebanding cutting station of KDT woodworking edge banding machines. It is listed as a cutting blade / cutting knife in alloy, in three sizes: 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm. One part number covers the three sizes the station takes.

The geometry is plain. The two wide plates are 100 and 106 mm long, 82 mm across and 7 mm thick, each with one locating hole and one continuous ground bevel along a long edge. The 110 × 20 × 13 mm blade is the narrow bar of the family, with a hole at each end and a milled relief between them.

Blades are wrapped in bubble wrap, packed in a heavy-duty cardboard box and labelled with a serial number. Send the size and the quantity; the price comes back against that order.

What these blades are, in the numbers that decide fit:

• Three sizes, one part number — 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm all sit under the single SKU EC043.
• Alloy body — the material field is the same for the three sizes: one alloy plate per blade, ground on the cutting edge.
• Blade, not cutting unit — the EC043 is listed as a cutting blade, so the worn part is the plate itself.
• One locating hole on the wide plates — the 100 and 106 mm blades each centre on a single hole, which fixes edge position on the seat.
• A hole at each end of the narrow bar — the 110 × 20 × 13 mm blade is held at both ends, with a milled relief between them.
• Ground bevel along a long edge — the edge is sharpened over the full 100 mm or 106 mm length, so banding is severed rather than crushed.
• 7 mm plate, 13 mm bar — the two wide plates carry 7 mm of body behind the bevel; the narrow blade carries 13 mm.
• Dimensioned for KDT edge banding machines — the three sizes are listed for the KDT cutting station, not for a generic holder.

A dull cutting blade leaves two bad choices: keep running it and trim every end by hand, or stop the line and wait for a part. A blade on the shelf ends both.

• The ragged end stops coming back. A ground bevel severs the banding square at the station, so a 100 mm cut does not have to be finished with a knife.
• You buy a blade, not a cutting unit. What wears is a 7 mm plate on the wide sizes and a 13 mm bar on the narrow one, not the head behind it.
• Six millimetres decide the fit. 100 and 106 mm are two separate parts, so measuring the old blade is what keeps the second order right.
• Three numbers, nothing guessed. Length, width and thickness — 110 × 20 × 13 mm on the narrow blade — decide whether it goes in.
• A dull edge costs minutes. A spare in the store room turns a change into one plate off its hole and back on, at the same seat setting.
• One material across the range. Alloy on the 100, 106 and 110 mm blades, so a store room stocks one family instead of three.
• Quoted on the order you place. Send size and quantity and the price comes back against them, from one blade to a shelf.

Yes, if one of the three sizes matches the blade in your station. The EC043 is listed as a cutting blade for KDT woodworking edge banding machines in 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm.

Measure the old blade — the size on the part decides it, not the machine model. The two wide plates are 100 and 106 mm long at 82 mm across and 7 mm thick, so they look alike on a bench; the narrow blade is 110 × 20 × 13 mm and does not interchange with either.

Alloy. That is the material field for the EC043, and it is the same for all three sizes, so the choice is between lengths and not between materials.

Just the blade. The EC043 is listed as a cutting blade / cutting knife, one plate per part, so nothing else on the station is replaced with it.

Read three dimensions off your old blade: length, width and thickness. 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm are the three on this page; the 6 mm between the two wide plates is enough to tell them apart.

Bubble wrap inside a heavy-duty cardboard box, with a serial number label on the package, so the part arrives as it left the store.

Yes. Orders are shipped internationally by carrier, and the packing is built for that trip: bubble wrap and a heavy-duty cardboard box around every blade.

Send me the measurement before you order rather than picking the nearest size. The three sizes here are 100 × 82 × 7 mm, 106 × 82 × 7 mm and 110 × 20 × 13 mm, and a blade that differs from them is not the same part.