Buffing Wheel for Edgebander 150X50X20mm Automatic Edgebander Polishing Wheels

Replacing the buffing wheel on an automatic edgebander? BW003 is φ150*φ50*φ20 mm — 150 mm outside diameter, 50 mm centre hole, 20 mm thick — in cotton cloth and steel. Those three numbers are the whole fit check against the polishing spindle. It is listed for woodworking edge banding machines, where the cotton face is the part that meets the band. Price is quoted on enquiry.

Two things go wrong with an edgebander buffing wheel, and both are avoidable. A wheel bought by eye arrives with the wrong centre hole, so it will not seat on the spindle, or it runs out of true. A cotton face loaded with glue residue stops polishing and starts smearing, so the band leaves the station dull. The third cost is the wait: no spare, station idle until a replacement lands.

BW003 is the replacement for that station. It measures φ150*φ50*φ20 mm: 150 mm outside diameter, 50 mm centre hole, 20 mm thickness. As a fit check, the 50 mm bore decides whether the wheel mounts at all, the 150 mm rim sets the contact circle along the band, and the 20 mm face is the width of cotton meeting the edge in one pass.

Material is listed as cotton and steel; the description names cotton cloth and metal. The face is cloth in multiple layers, which carries polish against the band instead of scraping it. The stated application is woodworking edge banding machines, specifically automatic edge banding devices — the wheel that presses on the band at the polishing station.

Fitting is the swap itself: worn wheel off, BW003 150x50x20 mm wheel on, station back in service. Price comes by enquiry, and a station taking a size other than φ150*φ50*φ20 mm is quoted from the dimensions you send.

Dimensions and material are the two things that decide whether a buffing wheel does its job, so both are written as numbers below.

• φ150 mm outside diameter — the rim that runs against the edge, fixed at 150 mm, not a range.
• 50 mm centre hole — the mounting bore; the wheel is made to mount on a 50 mm spindle.
• 20 mm face width — the cotton face measures 20 mm across the bore, the working width.
• Cotton cloth face — cloth in multiple layers is the surface that contacts the band, so polish is carried on fibre.
• Cotton and steel materials — both are named in the parameter table, and the description gives cotton cloth and metal.
• Automatic edge banding devices — the device class the listing names, which is where the buffing step sits on a production line.
• Woodworking edge banding machines — the machine family given as the application, so the compatibility question starts from the right station.
• One-for-one replacement — remove the worn wheel, fit the BW003 wheel on the same 50 mm bore; installation and maintenance are listed as simple.
• Spare on the shelf — the wheel is sold as a replaceable part, so a worn one is swapped rather than worked around.
• Other sizes on enquiry — anything outside φ150*φ50*φ20 mm is quoted against the dimensions you supply.

When a polishing station stops delivering, there are two ways out: pull panels for a hand pass, or keep the right wheel on the shelf. This wheel serves the second route, and three numbers decide it.

• Fit is settled before you order. 150 mm outside, 50 mm bore, 20 mm thick — measure the spindle and the order is decided.
• One part number, one reorder. BW003 brings back the same 150x50x20 mm wheel, so a repeat order does not drift in thickness.
• The working face is fibre. Cotton cloth in multiple layers holds polish at the surface that touches the band, which is why it is sold as a polishing wheel.
• Stoppage is measured in minutes. The wheel is a straight swap on the 50 mm bore, with no outside finishing job to wait for.
• Dull edges stop leaving the line. A fresh cotton face polishes where a loaded one smears, which is the gap between a saleable edge and a rework pile.
• Bench time is what you remove. Every edge polished at the station is an edge that does not go to a hand pass afterwards.
• A named application, not a guess. Woodworking edge banding machines and automatic edge banding devices are both named there.
• Non-standard sizes stay open. Other dimensions are quoted from the numbers you send, so an odd station is a quote, not a refusal.

Yes, if your polishing spindle takes a 50 mm bore. The wheel is φ150*φ50*φ20 mm — 150 mm outside diameter, 50 mm centre hole, 20 mm thick — and woodworking edge banding machines are the application it is listed for. Measure the spindle before ordering.

φ150*φ50*φ20 mm: 150 mm outside diameter, 50 mm centre hole, 20 mm thickness. All three are fixed for SKU BW003, and those three numbers are the only fit check the wheel needs.

Cotton and steel. The parameter table lists both, and the product description gives cotton cloth and metal, with the cloth in multiple layers as the working face.

Both names describe the same part. It is listed as a buffing wheel for edgebander and as edge bander tools — buffing wheels, and the cloth face is what does the polishing.

Woodworking edge banding machines, with automatic edge banding devices named as the machine type. That is the station where the wheel presses against the banded edge.

Take the worn wheel off the polishing spindle and fit the BW003 wheel on the same 50 mm bore. Installation and maintenance are listed as simple, and the worn wheel is replaced one for one.

Yes, by enquiry. Anything other than φ150*φ50*φ20 mm is quoted from the dimensions you send — outside diameter, centre hole and thickness — rather than matched by eye.

Price is quoted per enquiry; no figure is published. Send SKU BW003 and the quantity you need and the quote is raised against that.