Press Roller Rubber Wheel 48*8*12mm for SCM or KDT Edge Banding Machine Spare Parts

Need the pressure roller on a KDT or SCM edge bander to keep pressing evenly? This is the rubber replacement wheel for that position: 48 mm outside diameter, 8 mm bore, 12 mm thick. The rubber face grips PVC, melamine and veneer tape and holds it flat on the panel edge instead of letting it ride up. It is spare part PSW004, listed for KDT and SCM woodworking edge banding machines, and available in ten sizes from 48*8*12 mm to 70*18*25 mm.

A worn pressure roller does not announce itself at the roller. It shows up further down the line: tape lifting at the trailing corner, a glue line that opens on one side of the panel, and a stop while somebody finds a replacement in the right bore. That third stop is the one that costs the shift.

The PSW004 is a rubber pressure roller wheel for the press position on KDT and SCM woodworking edge banding machines: 48 mm outside diameter, 8 mm bore, 12 mm thickness. The bore is the dimension that decides the fit, so measure the shaft across the diameter before ordering — nothing else on the wheel compensates for a bore that is one millimetre out.

The body is rubber, as the specification lists it, and the rubber is the point of the part. It gives slightly under the pressure arm, so the contact band follows the tape instead of skidding over it, and the same force reaches every millimetre of the 12 mm face. The wheel is listed for PVC, melamine and veneer edge tapes on the same machine.

One wheel covers 48*8*12 mm and nothing else, so a repeat order runs the same as the wheel on the machine today. The rest of the family is listed in 65*8*25, 65*8*14, 60*12*20, 60*8*23, 60*8*24, 48*8*25, 67*8*25, 67*8*27 and 70*18*25 mm.

What decides whether the wheel works is the bore and the rubber.

• 48 mm outside diameter — the face that rides the tape is 48 mm across, the size the pressure arm is built around.
• 8 mm bore — the hole through the middle is 8 mm, so the shaft has to measure 8 mm across the diameter.
• 12 mm face — the rubber is 12 mm thick, narrow enough to sit on the glued tape and clear the board behind it.
• Rubber body — rubber is the listed material; it gives under the pressure arm and follows the tape instead of skidding across it.
• For KDT and SCM edge banders — the listing names both machine families, so the wheel is matched to a machine, not guessed at.
• PVC, melamine and veneer — one wheel is listed for all three tapes, so a tape change does not pull a second spare off the shelf.
• Direct replacement — it is a spare part for the pressure roller position, so the worn wheel comes off and this one goes on.
• Nine other sizes — the same family runs 65*8*25, 65*8*14, 60*12*20, 60*8*23, 60*8*24, 48*8*25, 67*8*25, 67*8*27 and 70*18*25 mm.
• One reference number — PSW004 stays the same between orders, so the wheel bought next quarter is the wheel fitted today.

The usual choice at a worn pressure roller is to run it until the edge shows, or to stop the line and chase a part whose size is not written anywhere.

• The corner stops lifting. A 12 mm rubber face that still deforms presses the tape flat across its width, so the open glue line at the trailing corner does not come back on the next panel.
• No adapter to make. The bore is 8 mm as supplied, so the only thing that changes at the shaft is the worn wheel itself.
• One part number for one position. PSW004 is a single repeatable 48*8*12 mm size, so the wheel ordered next month fits the way today's wheel fits.
• One spare covers three tapes. The wheel is listed for PVC, melamine and veneer, so a job change is a tape change, not a second purchase.
• A second size is an order line. Nine other dimensions in the same family, from 48*8*25 to 70*18*25 mm, come from the same place, so a second machine does not mean a second supplier.
• The spare costs less than the stop. It is a hand-sized rubber wheel, so one kept at the machine turns a worn face into a swap inside a shift instead of a wait for a purchase order.

Yes, if the pressure roller position on your machine takes a 48 mm wheel with a 8 mm bore and a 12 mm face. Those are the three dimensions of PSW004, and the bore is the one that decides the fit, so measure the shaft across the diameter before ordering.

They are the outside diameter, the bore and the thickness, all in millimetres. 48 mm is the face that rides the tape, 8 mm is the hole for the shaft, and 12 mm is how thick the rubber is.

Yes, the same part. It is listed as Pressure Wheels, Press Roller, Pressure Roller, Press Wheel and pressure rubber wheel, so any of those names brings you to the same 48*8*12 mm rubber wheel.

PVC, melamine and veneer. The wheel is listed for those three edge banding materials, so a tape change on the same machine does not need a different roller.

Rubber. The specification lists the body as rubber, with the 48*8*12 mm dimensions measured on the finished wheel: 48 mm outside, 8 mm bore, 12 mm thick.

No. It is supplied as a spare part for the pressure roller position, so the worn wheel comes off the shaft and this one goes on in its place.

Yes. The same family is listed in 65*8*25, 65*8*14, 60*12*20, 60*8*23, 60*8*24, 48*8*25, 67*8*25, 67*8*27 and 70*18*25 mm, so send the size your machine takes.

Price is quoted per order. Send the SKU PSW004, the size 48*8*12 mm and the quantity you need, and the reply covers price, minimum order and lead time together.