CCE001C 80*61.5mm Chain Pads Conveyance Pad For KDT Edge Bander Edge Banding Machine

Replacing worn chain pads on a KDT edge bander takes one measurement, not a part-number search. The CCE001C is an 80 x 61.5 mm conveyance pad that seats in the chain link and carries the panel past the working units: 80 mm along the chain, 61.5 mm across the panel contact, 0.1 kg per pad, rubber and plastic, grey face on a black base, textured for grip, supplied new and bulk packed from Guangdong, China. Measure one pad off your track, compare two numbers, order the set.

A worn conveyance pad on a KDT edge bander never stops the machine. The panel rides low at that one link, the pressure rollers hold it harder, and the glued edge reaches the trimmer with a line down one side. Then the same three costs: pads stay on the chain because nobody has the part number, scrap runs while a replacement is looked up, and the pad that comes is the wrong size because the old one was never measured.

The CCE001C is that replacement: a conveyance pad for the KDT edge bander and edge banding machine, one block in the chain link that carries the workpiece past the glue, trimming and buffing units. Each pad is 80 mm long and 61.5 mm wide — length in the direction of travel, width is the face the panel sits on.

Body is rubber and plastic, 0.1 kg per pad, grey on the pad face and black on the base. The top face is textured: the pattern raises traction, so the panel does not slip or drift sideways while the chain feeds it, and a panel that arrives square at the trimming units keeps a straight edge.

Pads are supplied new, bulk packed in standard packing, from Guangdong, China. The same block repeats along the track, so quantity follows chain length, not a fixed set.

What the two dimensions, the material and the contact face tell you before a pad goes back on the link:

• 80 x 61.5 mm seat — 80 mm along the chain, 61.5 mm across the panel contact, both off the worn pad, not a catalogue.
• Rubber and plastic body — 0.1 kg per pad: a face that grips the board on a base that holds its shape.
• Textured contact face — the pattern raises traction, so the panel does not slip or drift sideways through the feed.
• One height along the track — a full set puts every link back at the same level, which is what keeps the edge square.
• Black base, grey face — glue and dust change a used pad, so a worn face reads against a new one.
• Repeat block — one pad fills one link position, so quantity follows chain length, not a fixed set.
• New, not reconditioned — the contact face arrives with its full pattern instead of a flattened one.
• Bulk packed — standard bulk packing, so a full chain set arrives as one lot.
• KDT listing — listed for the KDT edge bander and edge banding machine, not a universal pad.
• Two-number fit check — length and width are the whole check; no machine number is needed to order.

The usual choice on a worn track is to run the pad flat or to pull the chain and guess the size.

• One flat reference again. A worn pad lowers the panel at that link; a set of 80 x 61.5 mm pads puts every link back to one height.
• The line on the edge goes away. A track low at one position marks the edge on one side and leaves the other clean, which gets billed as a cutter fault.
• Two numbers, no catalogue search. 80 mm by 61.5 mm off the old pad is the whole fit check, so ordering needs no machine serial.
• Grip where the cutters start. The textured face holds the board square to the chain, so the trimmer meets an edge still where it was.
• A face that gives up first. The textured face is the part that wears, so wear lands on a 0.1 kg block instead of on the panel.
• No machine adjustment. The pad seats in the link, so chain tension and track height stay as they were.
• Reorder without a drawing. CCE001C plus 80 x 61.5 mm matches the next delivery to the pads already on the chain.
• Change them as a set. Pads wear together along the track, so one order covers the whole chain instead of six single replacements.

Yes, if the pad on your chain measures 80 x 61.5 mm. It is listed for the KDT edge bander and edge banding machine, so pull one worn pad off the track, measure length and width, and compare the two numbers before ordering a set.

80 mm long and 61.5 mm wide. Length runs in the direction of travel and width is the face the panel sits on, so measure the old pad the same way.

0.1 kg. That is one pad, so a set for a full track is that figure times the number of link positions you count on the machine.

Rubber and plastic. The contact face is the part the board slides on, and it is textured so the panel grips instead of drifting.

Grey on the pad face, black on the base. Used pads take on glue and dust, so a worn set reads differently from a new one.

New. Condition is listed as new, and they ship bulk packed in standard packing from Guangdong, China.

Only KDT is confirmed. The CCE001C is listed for the KDT edge bander and edge banding machine; on another brand the 80 x 61.5 mm size and the link seat have to be checked against your own pad first.

Count them on your own track. The same block repeats along the chain, so the quantity follows track length, not a fixed set, and worn pads are changed together.