VCBL-K2-120x50x50 Q Vacuum Suction Cup for Woodworking CNC Machine Vacuum Block

Replacing a vacuum block that no longer holds a panel? The VCBL-K2 120x50x50 Q is a 120 × 50 mm block, 50 mm high, with a rubber sealing face on a plastic body, listed under part 10.01.12.00772. Arrangement is crossways. It is a spare for woodworking CNC machine vacuum tables and is specified for Homag CNC machining centres. The suction plate is sold as a separate spare, so a hardened face is replaced without the body. Price is quoted per enquiry; shipping by air, sea or express.

A nesting table that loses hold mid-cycle comes back to the same three things: a rubber face gone hard, so the panel creeps under the cutter; a block re-seated so often that it no longer sits flat and the seal leaks at one corner; and a replacement ordered from a photo that arrives on the wrong footprint.

The VCBL-K2 120x50x50 Q answers all three. It is a vacuum block for a woodworking CNC machine vacuum table: a plastic body with a bonded rubber sealing face, 120 × 50 mm in plan and 50 mm high. The plan size sets the seal area under the panel; the 50 mm height sets how far the panel rides above the console.

Arrangement is listed as crossways — the block sits crosswise on the console, not lengthwise. Material is rubber and plastic, and the split is functional: the plastic body carries the clamping load, the rubber face compresses and seals against the panel.

It is catalogued as a spare for CNC machines and specified for Homag CNC machining centres. The suction plate for the vacuum block is an available spare, so a worn face is replaced without discarding the body. Price is quoted per enquiry; shipping runs by air, by sea or by express.

Six numbers and one crossways position decide whether a block fits your console — these are the ones printed on this part.

• Measured, not nominal — the footprint is 120 × 50 mm and the height 50 mm, two figures a caliper can check before the block goes in.
• Height keeps your zero — 50 mm from base to pad face means the panel sits at the same level, so tool paths need no re-zero after a swap.
• Crossways, as the position expects — the block mounts crosswise on the console; a lengthwise block will not seat in that slot.
• Rubber face on a plastic body — the shell takes the clamping load, the rubber does the sealing, which is why the part is listed as rubber plus plastic.
• Two identifiers, one item — VCBL-K2 120x50x50 Q and part 10.01.12.00772 both point at this block, so either number can be quoted.
• Wear part sold separately — the suction plate for the vacuum block is an available spare, so the sealing face is replaced on its own.
• Listed for woodworking CNC — a spare for CNC machines, specified for Homag CNC machining centres and the vacuum-table work done on them.
• Quoted, not list-priced — price is per enquiry, so quantity and destination are the only two things you need to send.

The real choice is between running a hardened block until a panel shifts under the cutter, and holding a spare that costs a fraction of the panel it saves.

• A panel that stays put. 120 × 50 mm of rubber seals across its whole face, not on the few high spots left on a compressed old pad.
• A swap, not a fixture reset. 50 mm height matches the block being removed, so the change happens mid-job without touching the Z offset.
• Replace the face, keep the body. the suction plate is a separate spare, so the plastic body is not scrapped every time the rubber goes hard.
• Order by number. VCBL-K2 120x50x50 Q or 10.01.12.00772 on the item means nobody measures the old block or emails a photo to the supplier.
• One spare covers the floor. the same 120 × 50 × 50 mm block serves the Homag-type stations that take this size, so stock lines do not multiply with every machine.
• Keeps a spare on the shelf. quoted per enquiry and small enough to hold two or three, so a worn face is not a reason to stop a shift.
• Ships the way you already buy. air, sea or express, with freight confirmed once the destination is known.

A woodworking CNC machine vacuum table. It is catalogued as a spare for CNC machines and specified for Homag CNC machining centres. Match three figures against the block coming off: 120 × 50 mm footprint, 50 mm height, crossways arrangement.

120 × 50 mm in plan and 50 mm high. Length and width set the seal area under the panel, and height sets how far the panel rides above the console, so the 50 mm figure is the one that changes tool paths if it is wrong.

Yes, both numbers describe this one block. The parameter file lists VCBL-K2 120x50x50 Q as the model and 10.01.12.00772 as the part number, so either can be quoted on an enquiry or a purchase order.

No. The suction plate for the vacuum block is listed as an available spare, so the sealing face is replaced on its own and the plastic body stays in service. That is the part that hardens first under clamping load.

It means the block mounts crosswise on the console rather than along it. Fit is decided by the slot in the console — a lengthwise block of the same 120 × 50 mm footprint will not seat where a crossways one belongs.

Both, and the split is deliberate. The body is plastic and carries the clamping load; the face is rubber, which compresses and seals against the panel. Material is listed as rubber and plastic.

No — this listing is the block with its sealing face. Valve inserts, locating rings and gaskets are separate replacement parts; the suction plate for the vacuum block is the one spare listed against this item.

Price is quoted per enquiry — send the part number 10.01.12.00772 and the quantity. Shipping runs by air, by sea or by express, and freight is confirmed once the destination is known.