10.01.12.00628 Vacuum Suction Block For Schmalz 2-Circuit Console 125x75x50mm

Need the vacuum block that sits under a Schmalz 2-circuit console on a Homag CNC machine? This is it: 10.01.12.00628 (also written 10011200628), a suction block measuring 125 x 75 x 50 mm with a 50 mm body height, supplied in direction L with direction Q available as well. The body is moulded rubber and plastic, and the top rubber pads are available on their own, so a flat pad does not mean a new block. Price is quoted per order.

Anyone running a nesting table knows the three things that stop it: the rubber pad goes flat and the panel starts to creep, the block is ordered from abroad and sits in customs for weeks, and the replacement arrives in the wrong direction code because L and Q look alike on a parts list. This block is aimed at all three.

It is a vacuum suction block for the Schmalz 2-circuit console, the twin-circuit vacuum unit fitted to Homag woodworking CNC machines. Overall size is 125 x 75 x 50 mm, body height 50 mm, with 125 mm of length across the pad face. The directional variant is L; the Q version is also available, so a machine-side label reading Q is not a dead end.

The block is moulded in rubber and plastic: a plastic body carrying the circuit channels, and a rubber pad face that contacts the panel. Top rubber pads are available as their own item, which is what you want when the pad is worn but the block is still sound.

Ordering runs on numbers. 10.01.12.00628 and 10011200628 both identify this block, so a purchase order written either way reaches the same item. Price is quoted per order — send quantity and destination.

What the part is, in the numbers that matter:

• Two-circuit console fit — the body is made for the Schmalz 2-circuit console, so both vacuum circuits feed through one block instead of two separate cups.
• 125 x 75 x 50 mm envelope — 125 mm long, 75 mm wide, 50 mm tall, sized against the console seat rather than a generic cup.
• Direction L as standard — the L orientation ships as the default part; the Q orientation is available from the same block line.
• Dual numbering — 10.01.12.00628 and 10011200628 are one item under two formats, so either entry on your parts list resolves.
• Two-material body — moulded rubber and plastic, with a plastic core holding the ports and a rubber pad face in contact with the workpiece.
• Separate rubber pads — the top rubber pad is available as its own item, so pad wear becomes a pad order rather than a block order.
• Homag CNC spare — listed as a spare for Homag woodworking CNC machines, in the same reorder group as vacuum pads and locating parts.
• 50 mm stand-off — the block lifts the pad face 50 mm clear of the console, which sets where the panel sits on the table.
• Single-unit supply — one block per item; mixed orders and quantity breaks are quoted together on one request.

Two costs sit behind every vacuum block on a nesting table: the days the machine waits, and the panels that move under the tool.

• Pad wear stops the whole block. Because the top pad is a separate item, a worn pad costs one pad; the 125 x 75 x 50 mm block stays on the machine and stays in service.
• One part, two numbers. 10.01.12.00628 and 10011200628 both identify this block, so a purchase order raised from the machine plate or from your ERP lands on the same item.
• L now, Q on request. You do not carry a second part number for the other orientation — the Q variant comes off the same block line.
• Fit is dimensional, not approximate. 125 mm by 75 mm by 50 mm against a console built around that seat, so there is nothing to shim and no adapter to source.
• Two circuits, one seal face. A 2-circuit console needs both feeds routed; one block carries them, which leaves you a single pad face to inspect between shifts.
• Spare-part continuity. The block is listed as a Homag CNC spare, so it can sit on the same reorder line as pads and locating parts instead of being a one-off enquiry.
• Quoted per order. Send quantity and destination and the block is priced against that order, so mixed consignments are quoted once.

This block. The 125 x 75 x 50 mm suction block is sold as 10.01.12.00628 and as 10011200628 — one item, two formats — and it is built for the Schmalz 2-circuit console on Homag woodworking CNC machines.

L is the standard. If the marking on your machine reads Q, order that orientation — it is available from the same block, not a separate design, and you keep one part number family.

125 x 75 x 50 mm. That is 125 mm across the pad face, 75 mm wide and 50 mm tall, so the pad face stands 50 mm off the console seat.

Yes, if that console is the Schmalz 2-circuit type. The block is listed as a spare for Homag woodworking CNC machines; check the circuit count on the console and the 125 x 75 mm seat before ordering.

Yes. The top rubber pad is available as a separate item, so a pad that has gone flat or glazed can be replaced while the block itself stays in service.

Moulded rubber and plastic. A plastic body carries the vacuum circuits and a rubber pad face makes contact with the workpiece.

Yes. The block is made for the 2-circuit console, so both vacuum feeds are routed through one block instead of two separate cups.

Send the quantity and the destination for a quote. Price is quoted per order rather than carried as a list price, and mixed orders with other CNC spares are quoted together.