VCBL-K2-125x75x100 Vacuum Block For Homag CNC Machining Center Vacuum Cup 2056170930

Need to replace a vacuum pod on a Homag or Weeke machining center without re-datumming the table? The VCBL-K2-125X75X100 vacuum block is 125 × 75 × 100 mm and drops into the existing pod position. It holds wood, plastic and composite blanks for milling, routing and drilling. Both reference numbers — 2-056-17-0930 and 2056170930 — are supplied, and the vacuum block cover, brass filter and gasket are available on their own, so a worn seal does not become a new block.

Three things go wrong when a pod gives out on a nesting table: the blank lifts and the cut drifts, someone orders the wrong reference because the same block is listed as 2056170930 and 2-056-17-0930, and a flattened gasket turns a small wear item into a whole new block on the next purchase order. The VCBL-K2-125X75X100 is built to end all three.

It is a replacement vacuum block for Homag and Homag Weeke CNC machining centers, 125 × 75 × 100 mm in size, set into the pod position already on the table rather than into a new fixture. Wood, plastic and composite blanks all seat on the same 125 × 75 mm face, so a mixed-material job does not get re-clamped between parts.

The wear items are line items, not assemblies. A vacuum block cover, a brass filter and a gasket are each supplied on their own, so a filter packed with chips or a gasket flattened by clamping pressure is swapped in minutes. Both reference numbers, 2-056-17-0930 and 2056170930, are available on the same order.

What it does on the floor: milling, routing and drilling of nested parts, where a blank that creeps by a fraction loses the edge. Supplied by Shunhongyu from China, either branded or with a blank body, priced on request.

What decides whether a replacement pod holds the blank or eats the shift:

• Envelope that matches the pod position. 125 × 75 mm across the top and 100 mm tall, so the block drops into the slot already in the table.
• Two reference numbers, one block. 2-056-17-0930 and 2056170930 are both available, so the number on the machine and the number in the stores list both work.
• Cover replaced on its own. A scored or worn vacuum block cover is a separate part, so the body stays on the grid.
• Brass filter guards the port. Chips and dust stop at the brass filter instead of packing the vacuum channel; the filter lifts out, cleans and refits.
• Gasket is the sealing wear item. The gasket closes the vacuum against the blank, and a compressed one is replaced without touching the block body.
• Wood, plastic and composites. Three material families seat on the same 125 × 75 mm face: solid wood parts, plastic components and composite blanks.
• Milling, routing and drilling. One pod position covers all three operations on a nested sheet, so the table is dressed once.
• Homag and Weeke machining centers. Made for the pod positions of both machine families, with no adapter plate between block and table.
• Branded or blank body. Supplied under the Shunhongyu reference or with a blank body, whichever your listing needs.

When a pod fails, most shops choose between waiting on a delivery while the table sits idle and shimming the sheet to finish the run. This block is meant to remove that choice.

• The table keeps its datum. 125 × 75 × 100 mm is the envelope of the pod being removed, so nothing is re-referenced after the swap.
• A gasket does not cost a block. Cover, brass filter and gasket are ordered as separate line items, so the cheap part fails and the expensive part stays.
• Spares you can shelf. Filters and gaskets are small and light, so the next failure costs a shelf visit instead of a purchase order and a week of waiting.
• One block, three operations. Milling, routing and drilling run on the same pod, so a nested sheet is not re-clamped between operations.
• Material changes without a re-setup. Wood, plastic and composite blanks hold on the same 125 × 75 mm face.
• No adapter plate, no machining. The block goes into the existing Homag or Weeke pod position as delivered.
• Reference confusion ends. 2-056-17-0930 and 2056170930 are both supplied, so stores cannot order the wrong one of the two listings.
• Branding on your terms. Branded Shunhongyu or blank body, made in China, quoted per order.

Yes, if the pod position takes a 125 × 75 mm block 100 mm tall. Measure the block you are removing across its top face and its height; the VCBL-K2-125X75X100 is 125 × 75 × 100 mm and seats in the existing pod position of Homag and Homag Weeke CNC machining centers.

Yes — both references are supplied as this one block. The product data lists 2-056-17-0930 or 2056170930 as available, so quote either number and state which one your machine and your stores list use.

It is the block's size in millimetres: 125 × 75 mm across the top face and 100 mm tall. The top face decides which pod position and gasket fit; the height decides where the blank sits above the table.

No. The vacuum block cover, the brass filter and the gasket are all available as separate accessories, so a flattened gasket or a chip-packed filter is replaced on its own and the block body stays on the table.

Wood, plastic and composites. The block is listed for vacuum suction work on those three material families, which covers solid wood parts, plastic components and composite blanks on a nested sheet.

Milling, routing and drilling. The block is a vacuum suction cup for Homag CNC machining centers, and those three operations are the ones the product data lists for it.

No. It is a replacement vacuum block sold under our own reference VCBL-K2-125X75X100. Compare the size with the block you are removing — 125 × 75 × 100 mm — before you order.

Yes. The block is supplied either under the Shunhongyu reference or with a blank body, so a reseller listing can carry its own label. State which one you want when you request the quotation.